Lines Matching +full:board +full:- +full:2
17 2. System Requirement
36 - 2 ports multiport board
37 CP-102U, CP-102UL, CP-102UF
38 CP-132U-I, CP-132UL,
39 CP-132, CP-132I, CP132S, CP-132IS,
40 CI-132, CI-132I, CI-132IS,
41 (C102H, C102HI, C102HIS, C102P, CP-102, CP-102S)
43 - 4 ports multiport board
44 CP-104EL,
45 CP-104UL, CP-104JU,
46 CP-134U, CP-134U-I,
48 CP-114, CP-114I, CP-114S, CP-114IS, CP-114UL,
50 CI-104J, CI-104JS,
51 CI-134, CI-134I, CI-134IS,
52 (C114HI, CT-114I, C104P),
53 POS-104UL,
54 CB-114,
55 CB-134I
57 - 8 ports multiport board
58 CP-118EL, CP-168EL,
59 CP-118U, CP-168U,
63 CB-108
74 - msdiag
77 - msmon
79 - msterm A simple terminal program which is useful in testing serial
81 - io-irq.exe
92 or built-in into kernel (Static driver). You may refer to following
98 - Serial-HOWTO
99 - Kernel-HOWTO
101 2. System Requirement
104 - Hardware platform: Intel x86 machine
105 - Kernel version: 2.4.x or 2.6.x
106 - gcc version 2.72 or later
107 - Maximum 4 boards can be installed in combination
116 family multiport board.
118 ISA board
119 ---------
124 Please make sure the JP1 is open after the ISA board is set properly.
126 PCI/UPCI board
127 --------------
134 ---------------
136 Each port within the same multiport board shares the same IRQ. Up to
144 The driver file may be obtained from ftp, CD-ROM or floppy disk. The
171 -----------------------
174 two special file name for each serial port. One is dial-in port
178 Device naming when more than 2 boards installed
179 -----------------------------------------------
181 Naming convention for each Smartio/Industio multiport board is
182 pre-defined as below.
185 Board Num. Dial-in Port Callout port
186 1st board ttyM0 - ttyM7 cum0 - cum7
187 2nd board ttyM8 - ttyM15 cum8 - cum15
188 3rd board ttyM16 - ttyM23 cum16 - cum23
189 4th board ttyM24 - ttym31 cum24 - cum31
197 Board sequence
198 --------------
201 in the driver. After all specified ISA board activated, PCI board
203 Therefore the board number is sorted by the CAP address of ISA boards.
214 ------------- Prepare to use the MOXA driver --------------------
217 -------------------------------------------------
228 add/delete one MOXA board.
237 This shell script will require the major number for dial-in
239 to specify the total installed MOXA board number. Default major
240 numbers for dial-in device and callout device are 30, 35. If
246 3.4.2 Build the MOXA driver and utilities
247 -----------------------------------------
251 But you still re-compile the source code if you modify the source
270 ------------- Load MOXA driver--------------------
273 --------------------------
280 if "mxser" is activated. If the MOXA board is ISA board, the
284 ------------- Load MOXA driver on boot --------------------
287 ---------------------------
299 But if you use ISA board, please modify the "modprobe ..." command
320 --------------------------
324 board while activating "mxser.o". The format for parameters are
329 | | | +- 4th ISA board
330 | | +------ 3rd ISA board
331 | +------------ 2nd ISA board
332 +-------------------1st ISA board
341 3.5.1 Backup the built-in driver in the kernel
342 ----------------------------------------------
351 # ln -s linux-2.4 linux
353 3.5.2 Create link
354 -----------------
358 # ln -s /moxa/mxser/driver/mxser.c mxser.c
361 ------------------------------------------
365 In module mode, the CAP address for ISA board is given by
382 example, to driver 2 ISA boards with CAP address
383 0x280 and 0x180 as 1st and 2nd board. Just to change
389 --------------------------------
396 You will go into a menu-driven system. Please select [Character
397 devices][Non-standard serial port support], enable the [Moxa
398 SmartIO support] driver with "[*]" for built-in (not "[M]"), then
402 --------------------
414 make bzImage # take probably 10-20 minutes
430 --------------------------------------
437 ------------------
445 ------------
468 2 free major numbers for this driver. There are 3 steps to change
472 -----------------------------
475 in the system. Please select 2 major numbers that are available.
478 3.6.2 Create special files
479 --------------------------
485 -----------------------------------------
511 msdiag - Diagnostic
515 board found by driver in the system.
517 msmon - Port Monitoring
526 is started). You can reset all ports' count by <HOME> key. <+> <->
531 msterm - Terminal Emulation
546 uart set UART type(16450-->disable FIFO, 16550A-->enable FIFO)
572 More than 4 Moxa Smartio/Industio family boards found. Fifth board
576 To avoid this problem, please unplug fifth and after board, because Moxa
585 free IRQ and simply change another free IRQ for Moxa board.
588 Board #: C1xx Series(CAP=xxx) interrupt number invalid.
591 Each port within the same multiport board shares the same IRQ. Please set
592 one IRQ (IRQ doesn't equal to zero) for one Moxa board.
595 No interrupt vector be set for Moxa ISA board(CAP=xxx).
598 Moxa ISA board needs an interrupt vector.Please refer to user's manual