| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/iio/imu/ |
| D | adi,adis16480.txt | 30 * DIO1
34 If this field is left empty, DIO1 is assigned as default data ready
60 * DIO1
85 adi,ext-clk-pin = "DIO1";
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/iio/imu/ |
| D | adi,adis16480.yaml | 42 Default if not supplied is DIO1.
45 - DIO1
92 - DIO1
128 adi,ext-clk-pin = "DIO1";
|
| /kernel/linux/linux-6.6/arch/arm64/boot/dts/freescale/ |
| D | imx8mm-venice-gw71xx.dtsi | 62 "", "dio1", "", "", "", "", "", "",
160 MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x40000041 /* DIO1 */
|
| D | imx8mp-venice-gw71xx.dtsi | 59 "dio1", "", "", "dio0",
168 MX8MP_IOMUXC_SAI1_RXD6__GPIO4_IO08 0x40000146 /* DIO1 */
|
| D | imx8mm-kontron-bl-osm-s.dts | 141 gpio-line-names = "", "", "", "dio1-out", "", "", "dio1-in", "dio2-out",
|
| D | imx8mp-venice-gw72xx.dtsi | 94 "dio1", "", "", "dio0",
224 MX8MP_IOMUXC_SAI1_RXD6__GPIO4_IO08 0x40000146 /* DIO1 */
|
| D | imx8mm-venice-gw72xx.dtsi | 94 "", "dio1", "", "", "", "", "", "",
248 MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x40000041 /* DIO1 */
|
| D | imx8mp-venice-gw73xx.dtsi | 106 "dio1", "", "", "dio0",
253 MX8MP_IOMUXC_SAI1_RXD6__GPIO4_IO08 0x40000146 /* DIO1 */
|
| D | imx8mm-venice-gw73xx.dtsi | 114 "", "dio1", "", "", "", "", "", "",
285 MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x40000041 /* DIO1 */
|
| D | imx8mp-venice-gw74xx.dts | 249 "", "dio0", "", "dio1", "", "", "", "",
772 MX8MP_IOMUXC_GPIO1_IO11__GPIO1_IO11 0x40000040 /* DIO1 */
|
| /kernel/linux/linux-5.10/arch/x86/platform/ts5500/ |
| D | ts5500.c | 210 DEFINE_RES_IRQ_NAMED(7, "DIO1 interrupt"),
214 .name = "ts5500-dio1",
321 dev_warn(&pdev->dev, "DIO1 block registration failed\n"); in ts5500_init()
|
| /kernel/linux/linux-6.6/arch/x86/platform/ts5500/ |
| D | ts5500.c | 210 DEFINE_RES_IRQ_NAMED(7, "DIO1 interrupt"),
214 .name = "ts5500-dio1",
321 dev_warn(&pdev->dev, "DIO1 block registration failed\n"); in ts5500_init()
|
| /kernel/linux/linux-5.10/drivers/staging/pi433/ |
| D | pi433_if.c | 140 if (device->irq_state[DIO1] == DIO_FIFO_NOT_EMPTY_DIO1) { in DIO1_irq_handler()
142 } else if (device->irq_state[DIO1] == DIO_FIFO_LEVEL) { in DIO1_irq_handler()
149 "DIO1 irq: %d bytes free in fifo\n", device->free_in_fifo); in DIO1_irq_handler()
387 retval = rf69_set_dio_mapping(dev->spi, DIO1, DIO_FIFO_LEVEL); in pi433_start_rx()
390 dev->irq_state[DIO1] = DIO_FIFO_LEVEL; in pi433_start_rx()
391 irq_set_irq_type(dev->irq_num[DIO1], IRQ_TYPE_EDGE_RISING); in pi433_start_rx()
681 retval = rf69_set_dio_mapping(spi, DIO1, DIO_FIFO_LEVEL); in pi433_tx_thread()
684 device->irq_state[DIO1] = DIO_FIFO_LEVEL; in pi433_tx_thread()
685 irq_set_irq_type(device->irq_num[DIO1], IRQ_TYPE_EDGE_FALLING); in pi433_tx_thread()
|
| /kernel/linux/linux-6.6/drivers/staging/pi433/Documentation/devicetree/ |
| D | pi433-overlay.dtso | 45 DIO1-gpio = <&gpio 25 0>;
|
| D | pi433.txt | 40 DIO1-gpio = <&gpio 25 0>;
|
| /kernel/linux/linux-5.10/drivers/staging/pi433/Documentation/devicetree/ |
| D | pi433-overlay.dts | 45 DIO1-gpio = <&gpio 25 0>;
|
| D | pi433.txt | 40 DIO1-gpio = <&gpio 25 0>;
|
| /kernel/linux/linux-6.6/drivers/staging/pi433/ |
| D | pi433_if.c | 145 if (device->irq_state[DIO1] == DIO_FIFO_NOT_EMPTY_DIO1) { in DIO1_irq_handler()
147 } else if (device->irq_state[DIO1] == DIO_FIFO_LEVEL) { in DIO1_irq_handler()
154 "DIO1 irq: %d bytes free in fifo\n", device->free_in_fifo); in DIO1_irq_handler()
391 retval = rf69_set_dio_mapping(dev->spi, DIO1, DIO_FIFO_LEVEL); in pi433_start_rx()
394 dev->irq_state[DIO1] = DIO_FIFO_LEVEL; in pi433_start_rx()
395 irq_set_irq_type(dev->irq_num[DIO1], IRQ_TYPE_EDGE_RISING); in pi433_start_rx()
683 retval = rf69_set_dio_mapping(spi, DIO1, DIO_FIFO_LEVEL); in pi433_tx_thread()
686 device->irq_state[DIO1] = DIO_FIFO_LEVEL; in pi433_tx_thread()
687 irq_set_irq_type(device->irq_num[DIO1], IRQ_TYPE_EDGE_FALLING); in pi433_tx_thread()
|
| /kernel/linux/linux-5.10/drivers/gpio/ |
| D | gpio-ts5500.c | 15 * Blocks: DIO1, DIO2 and LCD port.
102 * TS-5500 DIO1 block
428 { "ts5500-dio1", TS5500_DIO1 },
|
| /kernel/linux/linux-6.6/drivers/gpio/ |
| D | gpio-ts5500.c | 15 * Blocks: DIO1, DIO2 and LCD port.
102 * TS-5500 DIO1 block
425 { "ts5500-dio1", TS5500_DIO1 },
|
| /kernel/linux/linux-6.6/drivers/iio/accel/ |
| D | adis16201.c | 59 /* Data-ready line selection: 1 = DIO1, 0 = DIO0 */
|
| /kernel/linux/linux-5.10/drivers/iio/accel/ |
| D | adis16201.c | 62 /* Data-ready line selection: 1 = DIO1, 0 = DIO0 */
|
| /kernel/linux/linux-5.10/drivers/staging/iio/accel/ |
| D | adis16203.c | 102 /* Data-ready line selection: 1 = DIO1, 0 = DIO0 */
|
| /kernel/linux/linux-6.6/drivers/staging/iio/accel/ |
| D | adis16203.c | 96 /* Data-ready line selection: 1 = DIO1, 0 = DIO0 */
|
| /kernel/linux/linux-5.10/drivers/iio/imu/ |
| D | adis16480.c | 167 [ADIS16480_PIN_DIO1] = "DIO1",
1085 * property. If it is not specified, use DIO1 pin as default. in adis16480_config_irq_pin()
1087 * ready signal. However, in the previous versions of the driver, DIO1 in adis16480_config_irq_pin()
|