Searched full:femto (Results 1 – 25 of 25) sorted by relevance
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/phy/ |
| D | qcom,usb-snps-femto-v2.yaml | 4 $id: "http://devicetree.org/schemas/phy/qcom,usb-snps-femto-v2.yaml#"
7 title: Qualcomm Synopsys Femto High-Speed USB PHY V2
20 - qcom,usb-snps-femto-v2-phy
|
| /kernel/linux/linux-5.10/arch/mips/include/asm/ |
| D | hpet.h | 58 /* Max HPET Period is 10^8 femto sec as in HPET spec */
61 * Min HPET period is 10^5 femto sec just for safety. If it is less than this,
|
| /kernel/linux/linux-6.6/arch/mips/include/asm/ |
| D | hpet.h | 58 /* Max HPET Period is 10^8 femto sec as in HPET spec */
61 * Min HPET period is 10^5 femto sec just for safety. If it is less than this,
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/phy/ |
| D | qcom,usb-snps-femto-v2.yaml | 4 $id: http://devicetree.org/schemas/phy/qcom,usb-snps-femto-v2.yaml#
7 title: Qualcomm Synopsys Femto High-Speed USB PHY V2
20 - qcom,usb-snps-femto-v2-phy
|
| /kernel/linux/linux-6.6/arch/x86/include/asm/ |
| D | hpet.h | 56 /* Max HPET Period is 10^8 femto sec as in HPET spec */
59 * Min HPET period is 10^5 femto sec just for safety. If it is less than this,
|
| /kernel/linux/linux-5.10/drivers/phy/qualcomm/ |
| D | Kconfig | 72 tristate "Qualcomm SNPS FEMTO USB HS PHY V2 module"
76 Enable support for the USB high-speed SNPS Femto phy on Qualcomm
|
| D | phy-qcom-snps-femto-v2.c | 300 { .compatible = "qcom,usb-snps-femto-v2-phy", },
379 .name = "qcom-snps-hs-femto-v2-phy",
387 MODULE_DESCRIPTION("Qualcomm SNPS FEMTO USB HS PHY V2 driver");
|
| D | Makefile | 13 obj-$(CONFIG_PHY_QCOM_USB_SNPS_FEMTO_V2)+= phy-qcom-snps-femto-v2.o
|
| D | phy-qcom-usb-hs-28nm.c | 228 * The Femto PHY is POR reset in the following scenarios. in qcom_snps_hsphy_por_reset()
|
| /kernel/linux/linux-5.10/arch/x86/include/asm/ |
| D | hpet.h | 56 /* Max HPET Period is 10^8 femto sec as in HPET spec */
59 * Min HPET period is 10^5 femto sec just for safety. If it is less than this,
|
| /kernel/linux/linux-6.6/drivers/phy/qualcomm/ |
| D | Kconfig | 167 tristate "Qualcomm SNPS FEMTO USB HS PHY V2 module"
171 Enable support for the USB high-speed SNPS Femto phy on Qualcomm
|
| D | Makefile | 24 obj-$(CONFIG_PHY_QCOM_USB_SNPS_FEMTO_V2)+= phy-qcom-snps-femto-v2.o
|
| D | phy-qcom-snps-femto-v2.c | 505 { .compatible = "qcom,usb-snps-femto-v2-phy", },
634 .name = "qcom-snps-hs-femto-v2-phy",
642 MODULE_DESCRIPTION("Qualcomm SNPS FEMTO USB HS PHY V2 driver");
|
| D | phy-qcom-usb-hs-28nm.c | 228 * The Femto PHY is POR reset in the following scenarios. in qcom_snps_hsphy_por_reset()
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/rtc/ |
| D | nxp,pcf8523.txt | 9 expressed in femto Farad (fF). Valid values are 7000 and 12500.
|
| D | nxp,pcf85063.txt | 13 expressed in femto Farad (fF). Valid values are 7000 and 12500.
|
| D | rtc.yaml | 32 The capacitive load of the quartz(x-tal), expressed in femto
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/rtc/ |
| D | nxp,pcf8523.txt | 9 expressed in femto Farad (fF). Valid values are 7000 and 12500.
|
| D | rtc.yaml | 31 The capacitive load of the quartz(x-tal), expressed in femto
|
| /kernel/linux/linux-5.10/include/uapi/linux/ |
| D | mmtimer.h | 34 * The resolution of the clock in femto (10^-15) seconds
|
| /kernel/linux/linux-5.10/include/linux/ |
| D | units.h | 21 #define FEMTO 1000000000000000ULL macro
|
| /kernel/linux/linux-6.6/include/uapi/linux/ |
| D | mmtimer.h | 34 * The resolution of the clock in femto (10^-15) seconds
|
| /kernel/linux/linux-6.6/include/linux/ |
| D | units.h | 21 #define FEMTO 1000000000000000ULL macro
|
| /kernel/linux/linux-5.10/drivers/char/ |
| D | uv_mmtimer.c | 71 * %MMTIMER_GETRES - Returns the resolution of the clock in femto (10^-15)
|
| /kernel/linux/linux-6.6/drivers/char/ |
| D | uv_mmtimer.c | 71 * %MMTIMER_GETRES - Returns the resolution of the clock in femto (10^-15)
|