Searched full:grounded (Results 1 – 25 of 42) sorted by relevance
12
| /kernel/linux/linux-6.6/drivers/pcmcia/ |
| D | bcm63xx_pcmcia.c | 128 /* VS1 grounded, VS2 float */
131 /* VS1 grounded, VS2 grounded */
137 /* VS1 grounded, VS2 tied to CD2 */
140 /* VS1 tied to CD2, VS2 grounded */
143 /* VS1 float, VS2 grounded */
155 /* VS2 grounded, VS1 is tied to CD1, CD2 is grounded */
|
| /kernel/linux/linux-5.10/drivers/pcmcia/ |
| D | bcm63xx_pcmcia.c | 128 /* VS1 grounded, VS2 float */
131 /* VS1 grounded, VS2 grounded */
137 /* VS1 grounded, VS2 tied to CD2 */
140 /* VS1 tied to CD2, VS2 grounded */
143 /* VS1 float, VS2 grounded */
155 /* VS2 grounded, VS1 is tied to CD1, CD2 is grounded */
|
| /kernel/linux/linux-6.6/Documentation/ABI/testing/ |
| D | sysfs-bus-iio-sx9324 | 10 + grounded (GD),
|
| /kernel/linux/linux-5.10/drivers/net/wireless/microchip/wilc1000/ |
| D | Kconfig | 22 To use this interface, pin9 (SDIO_SPI_CFG) must be grounded. Select
|
| /kernel/linux/linux-6.6/drivers/net/wireless/microchip/wilc1000/ |
| D | Kconfig | 22 To use this interface, pin9 (SDIO_SPI_CFG) must be grounded. Select
|
| /kernel/linux/linux-6.6/drivers/iio/accel/ |
| D | adxl345_i2c.c | 8 * 0x53 (ALT ADDRESS pin grounded)
|
| /kernel/linux/linux-5.10/drivers/iio/accel/ |
| D | adxl345_i2c.c | 8 * 0x53 (ALT ADDRESS pin grounded)
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/mfd/ |
| D | rohm,bd9576-pmic.yaml | 50 the ddr-sel pin low or high. Set this property if ddr-sel is grounded.
|
| /kernel/linux/linux-5.10/Documentation/spi/ |
| D | spi-lm70llp.rst | 69 and not grounded by the host via D7), the transistor conducts and switches
|
| /kernel/linux/linux-6.6/Documentation/spi/ |
| D | spi-lm70llp.rst | 69 and not grounded by the host via D7), the transistor conducts and switches
|
| /kernel/linux/linux-6.6/arch/arm64/boot/dts/ti/ |
| D | k3-j721s2-som-p0.dtsi | 47 /* standby pin has been grounded by default */
|
| /kernel/linux/linux-6.6/arch/arm/boot/dts/ti/omap/ |
| D | dra62x-j5eco-evm.dts | 131 /* USB0_ID pin state: SW10[1] = 0 cable detection, SW10[1] = 1 ID grounded */
|
| /kernel/linux/linux-5.10/arch/arm/boot/dts/ |
| D | dra62x-j5eco-evm.dts | 131 /* USB0_ID pin state: SW10[1] = 0 cable detection, SW10[1] = 1 ID grounded */
|
| D | ste-hrefv60plus.dtsi | 211 * (presumably pins are unconnected therefore grounded here,
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/iio/proximity/ |
| D | semtech,sx9324.yaml | 50 3 : grounded.
|
| /kernel/linux/linux-6.6/drivers/gpu/drm/amd/display/dc/gpio/ |
| D | hw_gpio.c | 111 * So (A) is grounded, output is driven by (EN = 0) in dal_hw_gpio_set_value()
|
| /kernel/linux/linux-5.10/drivers/gpu/drm/amd/display/dc/gpio/ |
| D | hw_gpio.c | 111 * So (A) is grounded, output is driven by (EN = 0) in dal_hw_gpio_set_value()
|
| /kernel/linux/linux-6.6/include/linux/usb/ |
| D | phy.h | 30 USB_EVENT_ID, /* id was grounded */
|
| /kernel/linux/linux-6.6/drivers/phy/ti/ |
| D | phy-omap-control.c | 138 * omap_control_usb_host_mode - set AVALID, VBUSVALID and ID pin in grounded
|
| /kernel/linux/linux-5.10/include/linux/usb/ |
| D | phy.h | 30 USB_EVENT_ID, /* id was grounded */
|
| /kernel/linux/linux-5.10/drivers/phy/ti/ |
| D | phy-omap-control.c | 138 * omap_control_usb_host_mode - set AVALID, VBUSVALID and ID pin in grounded
|
| /kernel/linux/linux-6.6/arch/arm/boot/dts/st/ |
| D | ste-hrefv60plus.dtsi | 253 * (presumably pins are unconnected therefore grounded here,
|
| /kernel/linux/linux-5.10/drivers/usb/musb/ |
| D | tusb6010.c | 403 /* REVISIT writeup of WID implies that if WID set and ID is grounded, in tusb_allow_idle()
579 /* If ID pin is grounded, we want to be a_idle */ in tusb_musb_set_vbus()
|
| /kernel/linux/linux-5.10/drivers/pwm/ |
| D | pwm-meson.c | 407 * The last 2 are grounded
|
| /kernel/linux/linux-6.6/drivers/pwm/ |
| D | pwm-meson.c | 352 * The last 2 are grounded
|
12