Searched full:soldered (Results 1 – 25 of 45) sorted by relevance
12
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/net/ |
| D | sff,sfp.txt | 8 "sff,sff" for soldered down SFF modules
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/net/ |
| D | sff,sfp.yaml | 17 - sff,sff # for soldered down SFF modules
|
| /kernel/linux/linux-6.6/arch/arm/boot/dts/allwinner/ |
| D | sun6i-a31s-sina31s.dts | 43 /* The SinA31s development board has the SinA31s core board soldered on */
|
| /kernel/linux/linux-5.10/arch/arm/boot/dts/ |
| D | sun6i-a31s-sina31s.dts | 43 /* The SinA31s development board has the SinA31s core board soldered on */
|
| D | armada-xp-openblocks-ax3-4.dts | 25 reg = <0 0x00000000 0 0x40000000>; /* 1 GB soldered on */
|
| D | stm32mp157c-ev1.dts | 354 * the connector. SB23 needs to be soldered in order to use it, and R77
|
| /kernel/linux/linux-5.10/Documentation/security/tpm/ |
| D | xen-tpmfront.rst | 109 The physical TPM that is soldered onto the motherboard.
|
| /kernel/linux/linux-6.6/Documentation/security/tpm/ |
| D | xen-tpmfront.rst | 109 The physical TPM that is soldered onto the motherboard.
|
| /kernel/linux/linux-6.6/arch/arm/boot/dts/marvell/ |
| D | armada-xp-openblocks-ax3-4.dts | 25 reg = <0 0x00000000 0 0x40000000>; /* 1 GB soldered on */
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/arm/ |
| D | fsl.yaml | 725 - const: dh,imx6ull-dhcom-som # The DHCOR is soldered on the DHCOM
990 variants. It is designed to be soldered on different carrier boards.
1020 variants. It is designed to be soldered on different carrier boards.
1109 variants. It is designed to be soldered on different carrier boards.
1241 TQMa93xxLA is designed to be soldered on different carrier boards.
1247 soldered on an adapter board or for the connector variant
|
| /kernel/linux/linux-5.10/arch/arm/mach-ixp4xx/ |
| D | Kconfig | 183 miniPCI slot 0 does not have a card connector soldered to the board
|
| /kernel/linux/linux-5.10/arch/arm64/boot/dts/amlogic/ |
| D | meson-gxl-s805x-libretech-ac.dts | 32 * The pads are present but no connector is soldered on
|
| /kernel/linux/linux-6.6/arch/arm64/boot/dts/amlogic/ |
| D | meson-gxl-s805x-libretech-ac.dts | 32 * The pads are present but no connector is soldered on
|
| /kernel/linux/linux-6.6/Documentation/firmware-guide/acpi/ |
| D | enumeration.rst | 544 For example, some systems use PCI devices soldered directly on the mother board,
554 Exar XR17V3521, soldered on the main board. This UART chip also includes
|
| /kernel/linux/linux-6.6/Documentation/networking/device_drivers/can/ |
| D | can327.rst | 326 Your adapter may have resistors soldered in which are meant to terminate
|
| /kernel/linux/linux-5.10/Documentation/i2c/ |
| D | instantiating-devices.rst | 256 * You are developing a driver on a test board, where you soldered the I2C
|
| /kernel/linux/linux-6.6/drivers/bluetooth/ |
| D | btsdio.c | 290 /* Broadcom devices soldered onto the PCB (non-removable) use an in btsdio_probe()
|
| /kernel/linux/linux-6.6/arch/arm/boot/dts/st/ |
| D | stm32mp157c-ev1.dts | 357 * the connector. SB23 needs to be soldered in order to use it, and R77
|
| /kernel/linux/linux-5.10/drivers/bluetooth/ |
| D | btsdio.c | 290 /* Broadcom devices soldered onto the PCB (non-removable) use an in btsdio_probe()
|
| /kernel/linux/linux-6.6/Documentation/i2c/ |
| D | instantiating-devices.rst | 264 * You are developing a driver on a test board, where you soldered the I2C
|
| /kernel/linux/linux-6.6/drivers/edac/ |
| D | ppc4xx_edac.c | 72 * boards (256 MiB w/o ECC memory soldered onto the board) and a
74 * soldered onto the board).
|
| /kernel/linux/linux-5.10/drivers/edac/ |
| D | ppc4xx_edac.c | 71 * boards (256 MiB w/o ECC memory soldered onto the board) and a
73 * soldered onto the board).
|
| /kernel/linux/linux-5.10/include/linux/ssb/ |
| D | ssb.h | 197 /* Information about the PCB the circuitry is soldered on. */
|
| /kernel/linux/linux-6.6/include/linux/ssb/ |
| D | ssb.h | 197 /* Information about the PCB the circuitry is soldered on. */
|
| /kernel/linux/linux-5.10/Documentation/driver-api/gpio/ |
| D | driver.rst | 237 In discrete designs, a pull-up or pull-down resistor is simply soldered on
|
12