Lines Matching +full:signal +full:- +full:id
3 Contact: linux-iio@vger.kernel.org
11 Contact: linux-iio@vger.kernel.org
16 MTCLKA-MTCLKB:
20 MTCLKC-MTCLKD:
26 Contact: linux-iio@vger.kernel.org
33 Contact: linux-iio@vger.kernel.org
39 Contact: linux-iio@vger.kernel.org
45 Contact: linux-iio@vger.kernel.org
52 Contact: linux-iio@vger.kernel.org
59 Contact: linux-iio@vger.kernel.org
78 non-recycle:
80 underflow takes place. The counter is re-enabled when a
84 modulo-n:
94 The output signal is initially low, and will remain low
95 until the counter reaches zero. The output signal then
99 hardware retriggerable one-shot:
100 The output signal is initially high. The output signal
101 will go low by a trigger input signal, and will remain
105 value and setting the output signal low, thus starting
106 the one-shot pulse.
109 The output signal is initially high. When the counter
110 has decremented to 1, the output signal goes low for one
111 clock pulse. The output signal then goes high again, the
116 The output signal is initially high.
120 expires, the output signal changes value and the
127 the count expires, the output signal goes low and the
135 The output signal is initially high. When the count
141 The output signal is initially high. Counting is started
142 by a trigger input signal. When the count expires, the
143 output signal will go low for one clock pulse and then
153 Contact: linux-iio@vger.kernel.org
161 Contact: linux-iio@vger.kernel.org
163 Read-only attribute that indicates the count direction of Count
174 Contact: linux-iio@vger.kernel.org
188 Contact: linux-iio@vger.kernel.org
190 Read-only attribute that indicates whether excessive noise is
195 Contact: linux-iio@vger.kernel.org
207 pulse-direction:
208 Rising edges on signal A updates the respective count.
209 The input level of signal B determines direction.
213 signal A updates the respective count; if the direction
214 is backward, falling edges on quadrature pair signal A
220 signal B updates the respective count; if the direction
221 is backward, falling edges on quadrature pair signal B
226 Any state transition on quadrature pair signal A updates
231 Any state transition on quadrature pair signal B updates
242 Contact: linux-iio@vger.kernel.org
244 Read-only attribute that indicates the device-specific name of
250 Contact: linux-iio@vger.kernel.org
259 Contact: linux-iio@vger.kernel.org
261 If the counter device supports preset registers -- registers
262 used to load counter channels to a set count upon device-defined
263 preset operation trigger events -- the preset count for channel
268 Contact: linux-iio@vger.kernel.org
275 Contact: linux-iio@vger.kernel.org
277 Action mode of Count Y for Signal Z. This attribute indicates
278 the condition of Signal Z that triggers the count function
283 Signal does not trigger the count function. In
284 Pulse-Direction count function mode, this Signal is
298 Contact: linux-iio@vger.kernel.org
324 Contact: linux-iio@vger.kernel.org
326 Read-only attribute that indicates the component ID of the
331 Contact: linux-iio@vger.kernel.org
340 Contact: linux-iio@vger.kernel.org
344 rounded-up to a power of 2.
348 Contact: linux-iio@vger.kernel.org
350 Read-only attribute that indicates the device-specific name of
356 Contact: linux-iio@vger.kernel.org
358 Read-only attribute that indicates the total number of Counts
363 Contact: linux-iio@vger.kernel.org
365 Read-only attribute that indicates the total number of Signals
370 Contact: linux-iio@vger.kernel.org
372 Read-only attribute that indicates whether a differential
374 for the respective channel of Signal Y. Valid attribute values
380 Contact: linux-iio@vger.kernel.org
383 respective channel of Signal Y is enabled. Valid attribute
388 Contact: linux-iio@vger.kernel.org
390 Filter clock factor for input Signal Y. This prescaler value
395 Contact: linux-iio@vger.kernel.org
397 Active level of index input Signal Y; irrelevant in
398 non-synchronous load mode.
403 Contact: linux-iio@vger.kernel.org
405 Discrete set of available values for the respective Signal Y
410 Contact: linux-iio@vger.kernel.org
412 Active level of Signal Y. The following polarity values are
416 Signal high state considered active level (rising edge).
419 Signal low state considered active level (falling edge).
423 Contact: linux-iio@vger.kernel.org
425 Read-only attribute that indicates the device-specific name of
426 Signal Y. If possible, this should match the name of the
427 respective signal as it appears in the device datasheet.
429 What: /sys/bus/counter/devices/counterX/signalY/signal
431 Contact: linux-iio@vger.kernel.org
433 Signal level state of Signal Y. The following signal level
444 Contact: linux-iio@vger.kernel.org
446 Configure the counter associated with Signal Y for
447 non-synchronous or synchronous load mode. Synchronous load mode
448 cannot be selected in non-quadrature (Pulse-Direction) clock
451 non-synchronous:
466 Contact: linux-iio@vger.kernel.org
468 Read-only attribute that indicates the signal Y frequency, in Hz.