Lines Matching +full:default +full:- +full:on
1 .. SPDX-License-Identifier: GPL-2.0+
8 Copyright(c) 1999 - 2013 Intel Corporation.
13 - Identifying Your Adapter
14 - Command Line Parameters
15 - Speed and Duplex Configuration
16 - Additional Configurations
17 - Support
22 For more information on how to identify your adapter, go to the Adapter &
29 networking link on the left to search for your adapter:
36 The default value for each parameter is generally the recommended setting,
50 -------
52 (Supported only on adapters with copper connections)
54 :Valid Range: 0x01-0x0F, 0x20-0x2F
55 :Default Value: 0x2F
57 This parameter is a bit-mask that specifies the speed and duplex settings
63 information on the AutoNeg parameter.
66 ------
68 (Supported only on adapters with copper connections)
70 :Valid Range: 0-2 (0=auto-negotiate, 1=half, 2=full)
71 :Default Value: 0
74 either one or two-directional. If both Duplex and the link partner are
75 set to auto-negotiate, the board auto-detects the correct duplex. If the
76 link partner is forced (either full or half), Duplex defaults to half-
80 -----------
82 :Valid Range: 0-3 (0=none, 1=Rx only, 2=Tx only, 3=Rx&Tx)
83 :Default Value: Reads flow control settings from the EEPROM
89 ---------------------
91 (not supported on Intel(R) 82542, 82543 or 82544-based adapters)
94 0,1,3,4,100-100000 (0=off, 1=dynamic, 3=dynamic conservative,
96 :Default Value: 3
100 adapter that is based on the maximum amount of interrupts that the adapter
106 load on the system and can lower CPU utilization under heavy load,
109 The default behaviour of the driver previously assumed a static
116 it dynamically adjusts the InterruptThrottleRate value based on the traffic
132 stepwise to 20000. This default mode is suitable for most applications.
140 In simplified mode the interrupt rate is based on the ratio of TX and
169 When e1000 is loaded with default settings and multiple adapters
170 are in use simultaneously, the CPU utilization may increase non-
179 of 2000 to 3000 interrupts per second works on a majority of
181 be platform-specific. If CPU utilization is not a concern, use
182 RX_POLLING (NAPI) and default driver settings.
185 -------------
188 - 48-256 for 82542 and 82543-based adapters
189 - 48-4096 for all other supported adapters
190 :Default Value: 256
198 on the MTU setting. The maximum MTU size is 16110.
202 Frames. Depending on the available system resources, the request
207 ----------
209 :Valid Range: 0-65535 (0=off)
210 :Default Value: 0
229 -------------
231 (This parameter is supported only on 82540, 82545 and later adapters.)
233 :Valid Range: 0-65535 (0=off)
234 :Default Value: 128
237 receive interrupt is generated. Useful only if RxIntDelay is non-zero,
244 -----
246 (This parameter is supported only on adapters with copper connections.)
249 :Default Value: 0 (auto-negotiate at all supported speeds)
253 partner is set to auto-negotiate, the board will auto-detect the correct
257 -------------
260 - 48-256 for 82542 and 82543-based adapters
261 - 48-4096 for all other supported adapters
262 :Default Value: 256
269 Depending on the available system resources, the request for a
274 ----------
276 :Valid Range: 0-65535 (0=off)
277 :Default Value: 8
286 -------------
288 (This parameter is supported only on 82540, 82545 and later adapters.)
290 :Valid Range: 0-65535 (0=off)
291 :Default Value: 32
294 transmit interrupt is generated. Useful only if TxIntDelay is non-zero,
296 packet is sent on the wire within the set amount of time. Proper tuning,
301 ------
303 (This parameter is NOT supported on the 82542-based adapter.)
305 :Valid Range: 0-1
306 :Default Value: 1
312 ---------
314 :Valid Range: 0-xxxxxxx (0=off)
315 :Default Value: 256
327 --------------------
329 :Valid Range: 0-1
330 :Default Value: 0 (disabled)
342 fiber interface board only links at 1000 Mbps full-duplex.
344 For copper-based boards, the keywords interact as follows:
346 - The default operation is auto-negotiate. The board advertises all
348 common speed and duplex mode IF the link partner is set to auto-negotiate.
350 - If Speed = 1000, limited auto-negotiation is enabled and only 1000 Mbps
351 is advertised (The 1000BaseT spec requires auto-negotiation.)
353 - If Speed = 10 or 100, then both Speed and Duplex should be set. Auto-
358 auto-negotiation process. It should be used when you wish to control which
359 speed and duplex combinations are advertised during the auto-negotiation
395 ------------
398 the default of 1500. Use the ifconfig command to increase the MTU size.
408 to the file /etc/sysconfig/network-scripts/ifcfg-eth<x>. This example
417 networking/ip-sysctl.txt for more details.
419 - The maximum MTU setting for Jumbo Frames is 16110. This value coincides
422 - Using Jumbo frames at 10 or 100 Mbps is not supported and may result in
425 - Adapters based on the Intel(R) 82542 and 82573V/E controller do not
432 -------
441 Enabling Wake on LAN (WoL)
442 --------------------------
446 WoL will be enabled on the system during the next shut down or reboot.
456 If an issue is identified with the released source code on the supported
458 to the issue to intel-wired-lan@lists.osuosl.org.