Home
last modified time | relevance | path

Searched +full:0 +full:x020000 (Results 1 – 5 of 5) sorted by relevance

/Documentation/devicetree/bindings/arm/
Dsp810.yaml70 reg = <0x020000 0x1000>;
76 assigned-clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>,
/Documentation/hwmon/
Dw83791d.rst10 Addresses scanned: I2C 0x2c - 0x2f
40 (default 0)
49 (default 0)
51 Use 'reset=1' to reset the chip (via index 0x40, bit 7). The default
56 a certain chip. Example usage is `force_subclients=0,0x2f,0x4a,0x4b`
57 to force the subclients of chip 0x2f on bus 0 to i2c addresses
58 0x4a and 0x4b.
90 set for each fan separately. Valid values range from 0 (stop) to 255 (full).
157 in0 (VCORE) 0x000001 0x000001
158 in1 (VINR0) 0x000002 0x002000 <== mismatch
[all …]
Dw83781d.rst10 Addresses scanned: I2C 0x28 - 0x2f, ISA 0x290 (8 I/O ports)
18 Addresses scanned: I2C 0x28 - 0x2f, ISA 0x290 (8 I/O ports)
26 Addresses scanned: I2C 0x2d
34 Addresses scanned: I2C 0x28 - 0x2f
52 Use 'init=0' to bypass initializing the chip.
56 (default 0)
62 a certain chip. Typical usage is `force_subclients=0,0x2d,0x4a,0x4b`
63 to force the subclients of chip 0x2d on bus 0 to i2c addresses
64 0x4a and 0x4b. This parameter is useful for certain Tyan boards.
80 | as99127f | 7 | 3 | 0 | 3 | 0x31 | 0x12c3 | yes | no |
[all …]
/Documentation/devicetree/bindings/pci/
Dnvidia,tegra20-pcie.txt27 - cell 0 specifies the bus and device numbers of the root port:
30 - cell 1 denotes the upper 32 address bits and should be 0
45 - 0x81000000: I/O memory region
46 - 0x82000000: non-prefetchable memory region
47 - 0xc2000000: prefetchable memory region
73 - pinctrl-0: phandle for the default/active state of pin configurations.
104 - If lanes 0 to 3 are used:
150 - Root port 0 uses 4 lanes, root port 1 is unused.
158 "pcie-N": where N ranges from 0 to the value specified in nvidia,num-lanes.
171 reg = <0x80003000 0x00000800 /* PADS registers */
[all …]
/Documentation/admin-guide/laptops/
Dthinkpad-acpi.rst153 (output in hex format: 0xAAAABBCC), where:
211 events. If a key is "masked" (bit set to 0 in the mask), the firmware
240 echo 0xffffffff > /proc/acpi/ibm/hotkey -- enable all hot keys
241 echo 0 > /proc/acpi/ibm/hotkey -- disable all possible hot keys
262 Returns 0.
269 to this value. This is always 0x80c, because those are
276 0: returns -EPERM
323 0 and 25 Hz. Polling is only carried out when strictly
337 attribute will read 0 if the switch is in the "radios
345 will read 0 if the ThinkPad is in normal mode, and
[all …]