Home
last modified time | relevance | path

Searched +full:0 +full:x0400 (Results 1 – 21 of 21) sorted by relevance

/Documentation/devicetree/bindings/pinctrl/
Damlogic,meson-pinctrl-a1.yaml27 "^bank@[0-9a-f]+$":
58 reg = <0x0400 0x003c>,
59 <0x0480 0x0118>;
63 gpio-ranges = <&periphs_pinctrl 0 0 62>;
/Documentation/devicetree/bindings/usb/
Dallwinner,sun4i-a10-musb.yaml96 reg = <0x01c13000 0x0400>;
97 clocks = <&ahb_gates 0>;
100 phys = <&usbphy 0>;
102 extcon = <&usbphy 0>;
/Documentation/hwmon/
Dasb100.rst10 Addresses scanned: I2C 0x2d
48 - 0x0001 => in0 (?)
49 - 0x0002 => in1 (?)
50 - 0x0004 => in2
51 - 0x0008 => in3
52 - 0x0010 => temp1 [1]_
53 - 0x0020 => temp2
54 - 0x0040 => fan1
55 - 0x0080 => fan2
56 - 0x0100 => in4
[all …]
/Documentation/devicetree/bindings/pci/
Drcar-gen4-pci-ep.yaml100 reg = <0 0xe65d0000 0 0x2000>, <0 0xe65d2000 0 0x1000>,
101 <0 0xe65d3000 0 0x2000>, <0 0xe65d5000 0 0x1200>,
102 <0 0xe65d6200 0 0x0e00>, <0 0xe65d7000 0 0x0400>,
103 <0 0xfe000000 0 0x400000>;
Drcar-gen4-pci-host.yaml98 reg = <0 0xe65d0000 0 0x1000>, <0 0xe65d2000 0 0x0800>,
99 <0 0xe65d3000 0 0x2000>, <0 0xe65d5000 0 0x1200>,
100 <0 0xe65d6200 0 0x0e00>, <0 0xe65d7000 0 0x0400>,
101 <0 0xfe000000 0 0x400000>;
117 bus-range = <0x00 0xff>;
119 ranges = <0x01000000 0 0x00000000 0 0xfe000000 0 0x00400000>,
120 <0x02000000 0 0x30000000 0 0x30000000 0 0x10000000>;
121 dma-ranges = <0x42000000 0 0x00000000 0 0x00000000 1 0x00000000>;
123 interrupt-map-mask = <0 0 0 7>;
124 interrupt-map = <0 0 0 1 &gic GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH>,
[all …]
/Documentation/devicetree/bindings/media/
Dqcom,sm8250-venus.yaml113 reg = <0x0aa00000 0xff000>;
129 iommus = <&apps_smmu 0x2100 0x0400>;
/Documentation/arch/arm/
Dnetwinder.rst15 0x0000 0x000f DMA1
16 0x0020 0x0021 PIC1
17 0x0060 0x006f Keyboard
18 0x0070 0x007f RTC
19 0x0080 0x0087 DMA1
20 0x0088 0x008f DMA2
21 0x00a0 0x00a3 PIC2
22 0x00c0 0x00df DMA2
23 0x0180 0x0187 IRDA
24 0x01f0 0x01f6 ide0
[all …]
/Documentation/devicetree/bindings/phy/
Dmediatek,xsphy.yaml20 u2 port0 0x0000 MISC
21 0x0100 FMREG
22 0x0300 U2PHY_COM
23 u2 port1 0x1000 MISC
24 0x1100 FMREG
25 0x1300 U2PHY_COM
26 u2 port2 0x2000 MISC
28 u31 common 0x3000 DIG_GLB
29 0x3100 PHYA_GLB
30 u31 port0 0x3400 DIG_LN_TOP
[all …]
/Documentation/userspace-api/media/v4l/
Dvidioc-g-sliced-vbi-cap.rst51 :header-rows: 0
52 :stub-columns: 0
73 - ``service_lines``\ [0][1]
78 - ``service_lines``\ [0][23]
104 - :cspan:`2` Drivers must set ``service_lines`` [0][0] and
105 ``service_lines``\ [1][0] to zero.
131 :stub-columns: 0
140 - 0x0001
148 - 0x0400
154 - 0x1000
[all …]
Dvidioc-g-tuner.rst69 :header-rows: 0
70 :stub-columns: 0
171 Ranging from 0 to 65535. Higher values indicate a better signal.
190 :header-rows: 0
191 :stub-columns: 0
215 :header-rows: 0
216 :stub-columns: 0
220 - 0x0001
224 - 0x0002
235 - 0x0004
[all …]
Dvidioc-queryctrl.rst93 this driver. Also note that the ``minimum`` value is not necessarily 0.
104 :header-rows: 0
105 :stub-columns: 0
152 0-511 and the driver reports 0-65535, step should be 128.
182 :header-rows: 0
183 :stub-columns: 0
233 0-511 and the driver reports 0-65535, step should be 128.
252 ``p + ((z * dims[1] + y) * dims[0] + x) * elem_size``.
260 never be 0.
264 control is not an array, then this field is 0.
[all …]
Ddev-sliced-vbi.rst116 :header-rows: 0
117 :stub-columns: 0
161 - ``service_lines``\ [0][1]
166 - ``service_lines``\ [0][23]
181 - :cspan:`2` Drivers must set ``service_lines`` [0][0] and
182 ``service_lines``\ [1][0] to zero. The
187 numbering starts at 1, not 0.
222 :stub-columns: 0
231 - 0x0001
239 - 0x0400
[all …]
/Documentation/admin-guide/laptops/
Dsonypi.rst89 set to 0xffffffff, meaning that all possible events
94 SONYPI_JOGGER_MASK 0x0001
95 SONYPI_CAPTURE_MASK 0x0002
96 SONYPI_FNKEY_MASK 0x0004
97 SONYPI_BLUETOOTH_MASK 0x0008
98 SONYPI_PKEY_MASK 0x0010
99 SONYPI_BACK_MASK 0x0020
100 SONYPI_HELP_MASK 0x0040
101 SONYPI_LID_MASK 0x0080
102 SONYPI_ZOOM_MASK 0x0100
[all …]
/Documentation/ABI/testing/
Dsysfs-class-mtd14 The /sys/class/mtd/mtd{0,1,2,3,...} directories correspond
63 0x0400: MTD_WRITEABLE - device is writable
64 0x0800: MTD_BIT_WRITEABLE - single bits can be flipped
65 0x1000: MTD_NO_ERASE - no erase necessary
66 0x2000: MTD_POWERUP_LOCK - always locked after reset
134 In the case of devices lacking any ECC capability, it is 0.
146 an error, 0 is returned. Higher layers (e.g., UBI) use this
186 devices lacking any ECC capability, it is 0.
197 devices lacking any ECC capability, it is 0.
208 devices lacking any ECC capability, it is 0.
/Documentation/networking/device_drivers/ethernet/3com/
Dvortex.rst91 Where N is a number from 0 to 7. Anything above 3 produces a lot
98 them with option 0x204 you would use::
100 options=0x204,0x204
108 0 10baseT
125 0x8000 Set driver debugging level to 7
126 0x4000 Set driver debugging level to 2
127 0x0400 Enable Wake-on-LAN
128 0x0200 Force full duplex mode.
129 0x0010 Bus-master enable bit (Old Vortex cards only)
134 insmod 3c59x options=0x204
[all …]
/Documentation/networking/device_drivers/ethernet/aquantia/
Datlantic.rst100 PHYAD: 0
126 version: 5.2.0-050200rc5-generic-kern
151 InErrors: 0
168 InDroppedDma: 0
169 Queue[0] InPackets: 23567131
170 Queue[0] OutPackets: 20070028
171 Queue[0] InJumboPackets: 0
172 Queue[0] InLroPackets: 0
173 Queue[0] InErrors: 0
176 Queue[1] InJumboPackets: 0
[all …]
/Documentation/driver-api/media/drivers/ccs/
Dccs-regs.asc19 module_model_id 0x0000 16
20 module_revision_number_major 0x0002 8
21 frame_count 0x0005 8
22 pixel_order 0x0006 8
23 - e GRBG 0
27 MIPI_CCS_version 0x0007 8
28 - e v1_0 0x10
29 - e v1_1 0x11
31 - f minor 0 3
32 data_pedestal 0x0008 16
[all …]
/Documentation/filesystems/ext4/
Dsuper.rst12 number is either 0 or a power of 3, 5, or 7. If the flag is not set,
29 * - 0x0
33 * - 0x4
37 * - 0x8
41 * - 0xC
45 * - 0x10
49 * - 0x14
53 is typically 0 for all other block sizes.
54 * - 0x18
58 * - 0x1C
[all …]
/Documentation/networking/
Dip-sysctl.rst11 - 0 - disabled (default)
12 - not 0 - enabled
48 Possible values: 0-3
65 Default: 0 (disabled)
69 - 0 - disabled
78 Default: 0
86 Default: 0 (disabled)
90 - 0 - disabled
97 Default: 0 (Layer 3)
101 - 0 - Layer 3
[all …]
/Documentation/scsi/
Dsym53c8xx_2.rst294 - target 2 all luns on controller 0 --> 15
295 - target 3 all luns on controller 0 --> 15
296 - target 4 all luns on controller 0 --> 7
297 - target 1 lun 0 on controller 1 --> 32
319 boot your system using 'sym53c8xx=verb:0' option.
321 apply "setverbose 0" control command to the proc fs entry
348 echo "<verb> <parameters>" >/proc/scsi/sym53c8xx/0
349 (assumes controller number is 0)
366 Specify a period of 0, to force asynchronous transfer mode.
379 :size: 0=8 bits, 1=16bits
[all …]
Dncr53c8xx.rst253 - SYM53C810 revision < 0x10 (16)
255 - SYM53C825 revision < 0x10 (16)
314 - target 2 all luns on controller 0 --> 15
315 - target 3 all luns on controller 0 --> 15
316 - target 4 all luns on controller 0 --> 7
317 - target 1 lun 0 on controller 1 --> 32
339 boot your system using 'ncr53c8xx=verb:0' option.
342 apply "setverbose 0" control command to the proc fs entry
365 /proc/scsi/ncr53c8xx/N (N=0,1,2 ....)
369 /proc/scsi/ncr53c8xx/0
[all …]