Home
last modified time | relevance | path

Searched +full:0 +full:x220 (Results 1 – 6 of 6) sorted by relevance

/Documentation/sound/
Dalsa-configuration.rst57 (0 = disable debug prints, 1 = normal debug messages,
71 Default: 0
80 the card #0. Similarly, when ``adsp_map=0``, /dev/adsp will be mapped
81 to PCM #0 of the card #0.
83 commas, such like ``dsp_map=0,1``.
98 Default: 0
119 Values: 0 through 31 or negative;
142 appearing card. They can do it by specifying "index=1,0" module
158 the port must be specified. For actual AdLib FM cards it will be 0x388.
170 64:0 OPL2 FM synth OPL2 FM Port
[all …]
/Documentation/devicetree/bindings/arm/apple/
Dapple,pmgr.yaml20 pattern: "^power-management@[0-9a-f]+$"
42 "power-controller@[0-9a-f]+$":
64 reg = <0x2 0x3b700000 0x0 0x14000>;
68 reg = <0x1c0 8>;
69 #power-domain-cells = <0>;
70 #reset-cells = <0>;
77 reg = <0x220 8>;
78 #power-domain-cells = <0>;
79 #reset-cells = <0>;
86 reg = <0x270 8>;
[all …]
/Documentation/bpf/
Dclassic_vs_extended.rst155 sub $0x228,%rsp
156 mov %rbx,-0x228(%rbp)
157 mov %r13,-0x220(%rbp)
159 mov $0x2,%esi
160 mov $0x3,%edx
161 mov $0x4,%ecx
162 mov $0x5,%r8d
166 mov $0x6,%esi
167 mov $0x7,%edx
168 mov $0x8,%ecx
[all …]
/Documentation/sound/cards/
Dmultisound.sh77 # 0x250, 0x260 or 0x270. This port can be disabled to have the card
96 # to obtain one with the command `pnpdump 1 0x203' -- this may vary
107 # io base 0x210, irq 5 and mem 0xd8000, and also sets the Kurzweil
108 # synth to 0x330 and irq 9 (may need editing for your system):
110 # (READPORT 0x0203)
115 # (CONFIGURE BVJ0440/-1 (LD 0
116 # (INT 0 (IRQ 5 (MODE +E))) (IO 0 (BASE 0x0210)) (MEM 0 (BASE 0x0d8000))
121 # (IO 0 (BASE 0x0330)) (INT 0 (IRQ 9 (MODE +E)))
140 # If you specify cfg=0x250 for the snd-msnd-pinnacle module, it
143 # on the card to 0x250, 0x260 or 0x270).
[all …]
/Documentation/arch/x86/
Dboot.rst28 Protocol 2.02 (Kernel 2.4.0-test3-pre3) New command line protocol.
99 0A0000 +------------------------+
121 0x100000 ("high memory"), and the kernel real-mode block (boot sector,
123 0x10000 and end of low memory. Unfortunately, in protocols 2.00 and
124 2.01 the 0x90000+ memory range is still used internally by the kernel;
139 0x90000 segment, the boot loader should make sure not to use memory
140 above the 0x9A000 point; too many BIOSes will break above that point.
149 0A0000 +------------------------+
180 following header at offset 0x01f1. The real-mode code can total up to
195 01FE/2 ALL boot_flag 0xAA55 magic number
[all …]
/Documentation/trace/
Dhistogram.rst226 field:unsigned short common_type; offset:0; size:2; signed:0;
227 field:unsigned char common_flags; offset:2; size:1; signed:0;
228 field:unsigned char common_preempt_count; offset:3; size:1; signed:0;
231 field:unsigned long call_site; offset:8; size:8; signed:0;
232 field:const void * ptr; offset:16; size:8; signed:0;
233 field:size_t bytes_req; offset:24; size:8; signed:0;
234 field:size_t bytes_alloc; offset:32; size:8; signed:0;
235 field:gfp_t gfp_flags; offset:40; size:4; signed:0;
288 Dropped: 0
305 allowed for the table (normally 0, but if not a hint that you may
[all …]