Home
last modified time | relevance | path

Searched +full:0 +full:x290 (Results 1 – 9 of 9) sorted by relevance

/Documentation/hwmon/
Dlm78.rst10 Addresses scanned: I2C 0x28 - 0x2f, ISA 0x290 (8 I/O ports)
20 Addresses scanned: I2C 0x28 - 0x2f, ISA 0x290 (8 I/O ports)
64 inputs can measure voltages between 0 and 4.08 volts, with a resolution
Dw83627hf.rst35 Use 'init=0' to bypass initializing the chip.
56 same pins as GPIO[0:4]. Technically, the `w83627_THF_` does not support a
80 isaset -y -f 0x2e 0x87
81 isaset -y -f 0x2e 0x87
85 isaset -y 0x2e 0x2f 0x07 0x0b
87 # Set the base I/O address (to 0x290 in this example)::
89 isaset -y 0x2e 0x2f 0x60 0x02
90 isaset -y 0x2e 0x2f 0x61 0x90
94 isaset -y -f 0x2e 0xaa
96 The above sequence assumes a Super-I/O config space at 0x2e/0x2f, but
[all …]
Dsis5595.rst58 force_addr=0xaddr Set the I/O base address. Useful for boards
64 Example: 'modprobe sis5595 force_addr=0x290'
102 inputs can measure voltages between 0 and 4.08 volts, with a resolution of
Dw83781d.rst10 Addresses scanned: I2C 0x28 - 0x2f, ISA 0x290 (8 I/O ports)
18 Addresses scanned: I2C 0x28 - 0x2f, ISA 0x290 (8 I/O ports)
26 Addresses scanned: I2C 0x2d
34 Addresses scanned: I2C 0x28 - 0x2f
52 Use 'init=0' to bypass initializing the chip.
56 (default 0)
62 a certain chip. Typical usage is `force_subclients=0,0x2d,0x4a,0x4b`
63 to force the subclients of chip 0x2d on bus 0 to i2c addresses
64 0x4a and 0x4b. This parameter is useful for certain Tyan boards.
80 | as99127f | 7 | 3 | 0 | 3 | 0x31 | 0x12c3 | yes | no |
[all …]
/Documentation/devicetree/bindings/spi/
Damlogic,a1-spifc.yaml40 reg = <0xfd000400 0x290>;
43 #size-cells = <0>;
/Documentation/PCI/
Dboot-interrupts.rst38 CPU: 0 PID: 2988 Comm: irq/34-nipalk Tainted: 4.14.87-rt49-02410-g4a640ec-dirty #1
43 ? dump_stack+0x46/0x5e
44 ? __report_bad_irq+0x2e/0xb0
45 ? note_interrupt+0x242/0x290
46 ? nNIKAL100_memoryRead16+0x8/0x10 [nikal]
47 ? handle_irq_event_percpu+0x55/0x70
48 ? handle_irq_event+0x4f/0x80
49 ? handle_fasteoi_irq+0x81/0x180
50 ? handle_irq+0x1c/0x30
51 ? do_IRQ+0x41/0xd0
[all …]
/Documentation/sound/cards/
Dmultisound.sh77 # 0x250, 0x260 or 0x270. This port can be disabled to have the card
96 # to obtain one with the command `pnpdump 1 0x203' -- this may vary
107 # io base 0x210, irq 5 and mem 0xd8000, and also sets the Kurzweil
108 # synth to 0x330 and irq 9 (may need editing for your system):
110 # (READPORT 0x0203)
115 # (CONFIGURE BVJ0440/-1 (LD 0
116 # (INT 0 (IRQ 5 (MODE +E))) (IO 0 (BASE 0x0210)) (MEM 0 (BASE 0x0d8000))
121 # (IO 0 (BASE 0x0330)) (INT 0 (IRQ 9 (MODE +E)))
140 # If you specify cfg=0x250 for the snd-msnd-pinnacle module, it
143 # on the card to 0x250, 0x260 or 0x270).
[all …]
/Documentation/trace/
Dhistogram.rst226 field:unsigned short common_type; offset:0; size:2; signed:0;
227 field:unsigned char common_flags; offset:2; size:1; signed:0;
228 field:unsigned char common_preempt_count; offset:3; size:1; signed:0;
231 field:unsigned long call_site; offset:8; size:8; signed:0;
232 field:const void * ptr; offset:16; size:8; signed:0;
233 field:size_t bytes_req; offset:24; size:8; signed:0;
234 field:size_t bytes_alloc; offset:32; size:8; signed:0;
235 field:gfp_t gfp_flags; offset:40; size:4; signed:0;
288 Dropped: 0
305 allowed for the table (normally 0, but if not a hint that you may
[all …]
/Documentation/networking/
Darcnet-hardware.rst269 values in the Linux ARCnet driver are only from 0x200 through 0x3F0. (If
272 a doc I got from Novell, MS Windows prefers values of 0x300 or more,
274 this may be because, if your card is at 0x2E0, probing for a serial port
275 at 0x2E8 will reset the card and probably mess things up royally.
277 - Avery's favourite: 0x300.
292 IRQ 0 Timer 0 (Not on bus)
340 Anything less than 0xA0000 is, well, a BAD idea since it isn't above
343 - Avery's favourite: 0xD0000
346 address from 0 to 255. Unlike Ethernet, you can set this address
349 on a network. DON'T use 0 or 255, since these are reserved (although
[all …]