Searched +full:0 +full:x2d (Results 1 – 25 of 37) sorted by relevance
12
| /Documentation/devicetree/bindings/usb/ |
| D | usb4604.txt | 7 - reg: Specifies the i2c slave address, it is required and should be 0x2d
16 reg = <0x2d>;
|
| D | microchip,usb5744.yaml | 83 #size-cells = <0>;
86 reg = <0x2d>;
92 #size-cells = <0>;
|
| /Documentation/i2c/ |
| D | old-module-parameters.rst | 31 # modprobe <driver> probe=1,0x2d
32 # modprobe <driver> force=1,0x2d
33 # modprobe <driver> force_<device>=1,0x2d
37 # echo <device> 0x2d > /sys/bus/i2c/devices/i2c-1/new_device
44 # modprobe <driver> ignore=1,0x2f
48 # echo dummy 0x2f > /sys/bus/i2c/devices/i2c-1/new_device
|
| D | instantiating-devices.rst | 44 reg = <0x50>;
51 reg = <0x60>;
82 I2C_BOARD_INFO("isp1301_omap", 0x2d),
86 I2C_BOARD_INFO("24c01", 0x52),
90 I2C_BOARD_INFO("24c01", 0x57),
123 I2C_BOARD_INFO("max6647", 0x4e),
149 static const unsigned short normal_i2c[] = { 0x2c, 0x2d, I2C_CLIENT_END };
159 memset(&i2c_info, 0, sizeof(struct i2c_board_info));
168 the OHCI adapter in question. It first tries at address 0x2c, if nothing
169 is found there it tries address 0x2d, and if still nothing is found, it
[all …]
|
| D | slave-testunit-backend.rst | 19 Instantiating the device is regular. Example for bus 0, address 0x30::
21 # echo "slave-testunit 0x1030" > /sys/bus/i2c/devices/i2c-0/new_device
31 reg = <(0x30 | I2C_OWN_SLAVE_ADDRESS)>;
36 byte. Its value is 0 if the testunit is idle, otherwise the command number of
46 0x00, CMD, which test to trigger
47 0x01, DATAL, configuration byte 1 for the test
48 0x02, DATAH, configuration byte 2 for the test
49 0x03, DELAY, delay in n * 10ms until test is started
65 0x00 NOOP
70 0x01 READ_BYTES
[all …]
|
| /Documentation/hwmon/ |
| D | lm85.rst | 10 Addresses scanned: I2C 0x2c, 0x2d, 0x2e
18 Addresses scanned: I2C 0x2c, 0x2d, 0x2e
26 Addresses scanned: I2C 0x2c, 0x2d, 0x2e
34 Addresses scanned: I2C 0x2c, 0x2d, 0x2e
42 Addresses scanned: I2C 0x2c, 0x2d, 0x2e
50 Addresses scanned: I2C 0x2c, 0x2d, 0x2e
58 Addresses scanned: I2C 0x2c, 0x2d, 0x2e
66 Addresses scanned: I2C 0x2c, 0x2d, 0x2e
74 Addresses scanned: I2C 0x2c, 0x2d, 0x2e
235 temperature. (PWM value from 0 to 255)
[all …]
|
| D | adm1025.rst | 10 Addresses scanned: I2C 0x2c - 0x2e
18 Addresses scanned: I2C 0x2c - 0x2d
24 * Only two possible addresses (0x2c - 0x2d).
|
| D | gl518sm.rst | 6 * Genesys Logic GL518SM release 0x00
10 Addresses scanned: I2C 0x2c and 0x2d
12 * Genesys Logic GL518SM release 0x80
16 Addresses scanned: I2C 0x2c and 0x2d
31 For the revision 0x00 chip, the in0, in1, and in2 values (+5V, +3V,
35 two revision of this chip, which we call revision 0x00 and 0x80. Revision
36 0x80 chips support the reading of all voltages and revision 0x00 only
64 a resolution of 0.019 volt. Note that revision 0x00 chips do not support
|
| D | adt7475.rst | 10 Addresses scanned: I2C 0x2C, 0x2D, 0x2E
18 Addresses scanned: I2C 0x2E
26 Addresses scanned: I2C 0x2C, 0x2D, 0x2E
34 Addresses scanned: I2C 0x2C, 0x2D, 0x2E
138 fan speed) is applied. PWM values range from 0 (off) to 255 (full speed).
143 At Tmin - hysteresis the PWM output can either be off (0% duty cycle) or at the
145 `pwm[1-*]_stall_disable sysfs attribute`. A value of 0 means the fans will shut
|
| D | emc6w201.rst | 10 Addresses scanned: I2C 0x2c, 0x2d, 0x2e
|
| D | adc128d818.rst | 10 Addresses scanned: I2C 0x1d, 0x1e, 0x1f, 0x2d, 0x2e, 0x2f
35 inputs can measure voltages between 0 and 2.55 volts, with a resolution
48 addresses 0x35 to 0x37. Those addresses are not scanned. You have to instantiate
|
| D | asb100.rst | 10 Addresses scanned: I2C 0x2d
48 - 0x0001 => in0 (?)
49 - 0x0002 => in1 (?)
50 - 0x0004 => in2
51 - 0x0008 => in3
52 - 0x0010 => temp1 [1]_
53 - 0x0020 => temp2
54 - 0x0040 => fan1
55 - 0x0080 => fan2
56 - 0x0100 => in4
[all …]
|
| D | nct7904.rst | 10 Addresses: I2C 0x2d, 0x2e
|
| D | amc6821.rst | 10 Addresses scanned: 0x18, 0x19, 0x1a, 0x2c, 0x2d, 0x2e, 0x4c, 0x4d, 0x4e
61 pwm1_mode rw Fan duty control mode (0=DC, 1=PWM)
63 pwm1_auto_point1_pwm ro Hardwired to 0, shared for both
75 0 degree C to 124 degree C in steps of
85 temp2_auto_point1_temp rw Must be between 0 degree C and 63 degree C and
92 0 degree C to 124 degree C in steps
107 load the module with: init=0.
113 - pwminv: 0 default pwm output, 1 inverts pwm output.
|
| /Documentation/devicetree/bindings/display/bridge/ |
| D | ti,sn65dsi83.yaml | 28 - 0x2c
29 - 0x2d
42 port@0:
91 - port@0
131 #size-cells = <0>;
135 reg = <0x2d>;
142 #size-cells = <0>;
144 port@0 {
145 reg = <0>;
|
| D | ti,sn65dsi86.yaml | 21 enum: [ 0x2c, 0x2d ]
80 port@0:
104 - 0
108 to either port 0 or port 1. Port 0 is suggested.
115 - 0
119 reordering but only on physical ports 0 and 1.
126 - 0
139 - 0
146 - port@0
168 #size-cells = <0>;
[all …]
|
| /Documentation/devicetree/bindings/leds/ |
| D | leds-lp8860.txt | 13 - #size-cells : 0
20 - reg : 0
36 #size-cells = <0>;
37 reg = <0x2d>;
41 led@0 {
42 reg = <0>;
|
| /Documentation/devicetree/bindings/phy/ |
| D | sunplus,sp7021-usb2-phy.yaml | 34 const: 0
65 reg = <0x9c004a80 0x80>, <0x9c000248 0x10>;
67 clocks = <&clkc 0x3d>;
68 resets = <&rstc 0x2d>;
69 #phy-cells = <0>;
72 sunplus,disc-vol-addr-off = <0>;
|
| /Documentation/devicetree/bindings/mfd/ |
| D | tps65912.txt | 26 reg = <0x2d>;
|
| /Documentation/devicetree/bindings/media/i2c/ |
| D | samsung,s5k5baf.yaml | 80 #size-cells = <0>;
84 reg = <0x2d>;
85 clocks = <&camera 0>;
89 stbyn-gpios = <&gpl2 0 GPIO_ACTIVE_LOW>;
|
| /Documentation/devicetree/bindings/display/panel/ |
| D | samsung,atna33xc20.yaml | 49 #size-cells = <0>;
53 reg = <0x2d>;
72 #size-cells = <0>;
74 port@0 {
75 reg = <0>;
|
| /Documentation/devicetree/bindings/power/supply/ |
| D | cw2015_battery.yaml | 61 #size-cells = <0>;
65 reg = <0x62>;
67 0x17 0x67 0x80 0x73 0x6E 0x6C 0x6B 0x63
68 0x77 0x51 0x5C 0x58 0x50 0x4C 0x48 0x36
69 0x15 0x0C 0x0C 0x19 0x5B 0x7D 0x6F 0x69
70 0x69 0x5B 0x0C 0x29 0x20 0x40 0x52 0x59
71 0x57 0x56 0x54 0x4F 0x3B 0x1F 0x7F 0x17
72 0x06 0x1A 0x30 0x5A 0x85 0x93 0x96 0x2D
73 0x48 0x77 0x9C 0xB3 0x80 0x52 0x94 0xCB
74 0x2F 0x00 0x64 0xA5 0xB5 0x11 0xF0 0x11
|
| /Documentation/devicetree/bindings/gpio/ |
| D | gpio-xgene-sb.txt | 25 0 = active high
30 - first cell is 0-N corresponding for EXT_INT_0 to EXT_INT_N.
40 reg = <0x0 0x17001000 0x0 0x400>;
43 interrupts = <0x0 0x28 0x1>,
44 <0x0 0x29 0x1>,
45 <0x0 0x2a 0x1>,
46 <0x0 0x2b 0x1>,
47 <0x0 0x2c 0x1>,
48 <0x0 0x2d 0x1>;
|
| /Documentation/devicetree/bindings/net/ |
| D | marvell-bt-8xxx.txt | 52 #size-cells = <0>;
60 0x37 0x01 0x1c 0x00 0xff 0xff 0xff 0xff 0x01 0x7f 0x04 0x02
61 0x00 0x00 0xba 0xce 0xc0 0xc6 0x2d 0x00 0x00 0x00 0x00 0x00
62 0x00 0x00 0xf0 0x00>;
63 marvell,wakeup-pin = /bits/ 16 <0x0d>;
64 marvell,wakeup-gap-ms = /bits/ 16 <0x64>;
72 #size-cells = <0>;
80 marvell,wakeup-pin = /bits/ 16 <0x0d>;
81 marvell,wakeup-gap-ms = /bits/ 16 <0x64>;
|
| /Documentation/devicetree/bindings/media/ |
| D | qcom,msm8996-venus.yaml | 114 reg = <0x00c00000 0xff000>;
122 iommus = <&venus_smmu 0x00>,
123 <&venus_smmu 0x01>,
124 <&venus_smmu 0x0a>,
125 <&venus_smmu 0x07>,
126 <&venus_smmu 0x0e>,
127 <&venus_smmu 0x0f>,
128 <&venus_smmu 0x08>,
129 <&venus_smmu 0x09>,
130 <&venus_smmu 0x0b>,
[all …]
|
12