Searched +full:0 +full:xf00 (Results 1 – 11 of 11) sorted by relevance
| /Documentation/devicetree/bindings/interrupt-controller/ |
| D | msi.txt | 86 reg = <0xa 0xf00>;
93 reg = <0xb 0xf00>;
101 reg = <0xc 0xf00>;
108 dev@0 {
109 reg = <0x0 0xf00>;
117 reg = <0x1 0xf00>;
123 msi-parent = <&msi_a>, <&msi_b 0x17>;
127 reg = <0x2 0xf00>;
133 msi-parent = <&msi_a>, <&msi_b 0x17>, <&msi_c 0x53>;
|
| /Documentation/devicetree/bindings/sound/ |
| D | mtk-btcvsd-snd.txt | 19 reg=<0 0x18000000 0 0x1000>,
20 <0 0x18080000 0 0x8000>;
23 mediatek,offset = <0xf00 0x800 0xfd0 0xfd4 0xfd8>;
|
| /Documentation/devicetree/bindings/clock/ |
| D | nxp,lpc3220-usb-clk.yaml | 33 reg = <0xf00 0x100>;
|
| /Documentation/devicetree/bindings/soc/bcm/ |
| D | brcm,bcm2711-avs-monitor.yaml | 37 reg = <0x7d5d2000 0xf00>;
41 #thermal-sensor-cells = <0>;
|
| /Documentation/devicetree/bindings/thermal/ |
| D | brcm,avs-ro-thermal.yaml | 29 const: 0
41 reg = <0x7d5d2000 0xf00>;
45 #thermal-sensor-cells = <0>;
|
| /Documentation/devicetree/bindings/ata/ |
| D | ata-generic.yaml | 42 default: 0
54 reg = <0x1a000 0x100>,
55 <0x1a100 0xf00>;
|
| /Documentation/devicetree/bindings/dma/ |
| D | brcm,bcm2835-dma.yaml | 16 0, 2 and 3 have special functionality and should not be used by the driver.
63 reg = <0x7e007000 0xf00>;
99 brcm,dma-channel-mask = <0x7f35>;
|
| /Documentation/devicetree/bindings/net/ |
| D | ti,k3-am654-cpsw-nuss.yaml | 19 The internal Communications Port Programming Interface (CPPI5) (Host port 0).
20 Host Port 0 CPPI Packet Streaming Interface interface supports 8 TX channels
27 Support for Audio/Video Bridging (P802.1Qav/D6.0)
31 IEEE P902.3br/D2.0 Interspersing Express Traffic
113 const: 0
169 "^mdio@[0-9a-f]+$":
176 "^cpts@[0-9a-f]+":
252 reg = <0x0 0x46000000 0x0 0x200000>;
254 ranges = <0x0 0x0 0x0 0x46000000 0x0 0x200000>;
260 pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>;
[all …]
|
| /Documentation/sound/hd-audio/ |
| D | notes.rst | 74 0 is the default value for all other
104 last cmd=0x12345678
106 last cmd=0x12345678
128 In such a case, turn the bit 8 (0x100) of ``probe_mask`` option on.
130 unconditionally. For example, ``probe_mask=0x103`` will force to probe
131 the codec slots 0 and 1 no matter what the hardware reports.
144 in the recent kernel, try to pass ``enable_msi=0`` option to disable
263 chance via SET_EAPD_BTL verb (0x70c). On others, GPIO pin (mostly
270 triggered. Issuing GET_PIN_SENSE verb (0xf09) may result in the
289 should be set to exactly 50%, corresponding to 0dB -- neither extra
[all …]
|
| /Documentation/scsi/ |
| D | arcmsr_spec.rst | 10 1. Message 0
38 offset 0xf00 for RS232 out (request buffer)
39 offset 0xe00 for RS232 in (scratch buffer)
40 offset 0xa00 for inbound message code message_rwbuffer
42 offset 0xa00 for outbound message code message_rwbuffer
71 0 256 bytes frame
75 0 normal request
92 bit31 must be 0 (for this type of reply)
96 0 no error, ignore AdapStatus/DevStatus/SenseData
112 offset: 0x78 Request Frame (bit30 == 1)
[all …]
|
| /Documentation/sound/ |
| D | alsa-configuration.rst | 57 (0 = disable debug prints, 1 = normal debug messages,
71 Default: 0
80 the card #0. Similarly, when ``adsp_map=0``, /dev/adsp will be mapped
81 to PCM #0 of the card #0.
83 commas, such like ``dsp_map=0,1``.
98 Default: 0
119 Values: 0 through 31 or negative;
142 appearing card. They can do it by specifying "index=1,0" module
158 the port must be specified. For actual AdLib FM cards it will be 0x388.
170 64:0 OPL2 FM synth OPL2 FM Port
[all …]
|