Searched full:133 (Results 1 – 25 of 31) sorted by relevance
12
| /Documentation/scsi/ |
| D | aic79xx.rst | 28 AIC-7901A Single Channel 64-bit PCI-X 133MHz to
30 AIC-7901B Single Channel 64-bit PCI-X 133MHz to
32 AIC-7902A4 Dual Channel 64-bit PCI-X 133MHz to
34 AIC-7902B Dual Channel 64-bit PCI-X 133MHz to
41 Adaptec SCSI Card 39320 Dual Channel 64-bit PCI-X 133MHz to 7902A4/7902B
44 Adaptec SCSI Card 39320A Dual Channel 64-bit PCI-X 133MHz to 7902B
47 Adaptec SCSI Card 39320D Dual Channel 64-bit PCI-X 133MHz to 7902A4
50 Adaptec SCSI Card 39320D Dual Channel 64-bit PCI-X 133MHz to 7902A4
54 Adaptec SCSI Card 29320 Single Channel 64-bit PCI-X 133MHz to 7901A
58 Adaptec SCSI Card 29320A Single Channel 64-bit PCI-X 133MHz to 7901B
[all …]
|
| D | arcmsr_spec.rst | 638 byte 3 0/1/2/3 (133/100/66/33)
700 (0/1/2/3/4, 33/66/100/133/150 for ide )
717 (0/1/2/3/4, 33/66/100/133/150 for ide )
821 (0/1/2/3/4->33/66/100/133/150 for IDE )
845 (0/1/2/3/4->33/66/100/133/150 for IDE )
|
| /Documentation/networking/device_drivers/ethernet/chelsio/ |
| D | cxgb.rst | 221 eth#: Chelsio N210 1x10GBaseX NIC (rev #), PCIX 133MHz/64-bit
307 chipset, you may experience the "133-Mhz Mode Split Completion Data
308 Corruption" bug identified by AMD while using a 133Mhz PCI-X card on the
313 is operating at 133 Mhz", causing data corruption.
318 For 133Mhz secondary bus operation, limit the transaction length and
327 section 56, "133-MHz Mode Split Completion Data Corruption" for more
|
| /Documentation/devicetree/bindings/pinctrl/ |
| D | qcom,sdx75-tlmm.yaml | 33 maxItems: 133
107 gpio-ranges = <&tlmm 0 0 133>;
|
| D | nxp,s32g2-siul2-pinctrl.yaml | 81 enum: [83, 133, 150, 166, 208]
|
| D | starfive,jh7100-pinctrl.yaml | 242 <PAD_FUNC_SHARE(133)>,
|
| /Documentation/devicetree/bindings/dma/ |
| D | milbeaut-m10v-hdmac.txt | 23 <0 133 4>,
|
| D | renesas,rz-dmac.yaml | 125 <GIC_SPI 133 IRQ_TYPE_EDGE_RISING>,
|
| /Documentation/devicetree/bindings/display/panel/ |
| D | visionox,vtdr6130.yaml | 54 reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
|
| /Documentation/devicetree/bindings/arm/omap/ |
| D | crossbar.txt | 38 ti,irqs-skip = <10 133 139 140>;
|
| /Documentation/devicetree/bindings/net/can/ |
| D | bosch,c_can.yaml | 104 interrupts = <0 131 4>, <0 132 4>, <0 133 4>, <0 134 4>;
|
| /Documentation/devicetree/bindings/iio/dac/ |
| D | adi,ad5758.yaml | 92 minimum: 133
|
| /Documentation/devicetree/bindings/sound/ |
| D | mt8186-afe-pcm.yaml | 143 <&topckgen 133>, //CLK_TOP_APLL12_CK_DIV2
|
| D | mediatek,mt8188-afe.yaml | 212 <&topckgen 133>, //CLK_TOP_APLL2_D4
|
| /Documentation/devicetree/bindings/net/ |
| D | hisilicon-hns-dsaf.txt | 67 interrupts = <131 4>,<132 4>, <133 4>,<134 4>,
|
| /Documentation/devicetree/bindings/gpio/ |
| D | gpio-davinci.yaml | 148 <GIC_SPI 133 IRQ_TYPE_EDGE_RISING>,
|
| /Documentation/userspace-api/media/dvb/ |
| D | ca_high_level.rst | 75 #define CA_SEND_MSG _IOW('o', 133, ca_msg_t)
|
| /Documentation/networking/device_drivers/ethernet/neterion/ |
| D | s2io.rst | 43 eth4: Device is on 64 bit 133MHz PCIX(M1) bus
|
| /Documentation/devicetree/bindings/ata/ |
| D | ceva,ahci-1v84.yaml | 177 interrupts = <0 133 IRQ_TYPE_LEVEL_HIGH>;
|
| /Documentation/devicetree/bindings/opp/ |
| D | opp-v2-kryo-cpu.yaml | 303 speedbin_efuse: speedbin@133 {
|
| /Documentation/admin-guide/media/ |
| D | bttv-cardlist.rst | 549 * - 133
|
| D | saa7134-cardlist.rst | 549 * - 133
|
| /Documentation/devicetree/bindings/usb/ |
| D | qcom,dwc3.yaml | 605 interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
|
| /Documentation/userspace-api/media/v4l/ |
| D | mt2110t.svg | 20 …33,58 679,27 624,-4 557,-20 476,-20 357,-20 271,10 216,69 161,128 133,225 133,361 L 133,1082 314,1…
|
| /Documentation/netlabel/ |
| D | draft-ietf-cipso-ipsecurity-01.txt | 40 categories or compartments, another security option (Type 133) exists and
|
12
