Searched full:additional (Results 1 – 25 of 785) sorted by relevance
12345678910>>...32
| /Documentation/kbuild/ |
| D | kbuild.rst | 36 Additional options to pass when preprocessing. The preprocessing options
42 Additional options to pass to $(CC_COMPAT) when preprocessing C and assembler
47 Additional options to the assembler (for built-in and modules).
51 Additional assembler options for modules.
55 Additional assembler options for built-in.
59 Additional options to the C compiler (for built-in and modules).
63 Additional options to the Rust compiler (for built-in and modules).
67 Additional options for $(CC) when used to compile
72 Additional module specific options to use for $(CC).
76 Additional options for $(RUSTC) when used to compile
[all …]
|
| /Documentation/devicetree/bindings/sound/ |
| D | wlf,wm8960.yaml | 56 - gpio-cfg[1]: {GPIOPOL:GPIOSEL[2:0]} of R48 (Additional Control 4).
63 - hp-cfg[0]: HPSEL[1:0] of R48 (Additional Control 4).
64 - hp-cfg[1]: {HPSWEN:HPSWPOL} of R24 (Additional Control 2).
65 - hp-cfg[2]: {TOCLKSEL:TOEN} of R23 (Additional Control 1).
70 If present, the LRCM bit of R24 (Additional control 2) gets set,
|
| /Documentation/ABI/testing/ |
| D | sysfs-bus-iio-ina2xx-adc | 9 in-driver readout rate at the cost of an additional register read.
12 save the additional i2c transaction, which will improve the bandwidth
|
| D | sysfs-class-led-multicolor | 11 For additional details please refer to
23 For additional details please refer to
|
| D | evm | 102 validate the EVM signature, and allows additional attributes
104 additional attributes are added (and on files possessing those
105 additional attributes) will only be valid if the same
106 additional attributes are configured on system boot. Writing
|
| D | sysfs-bus-iio-accel-bmc150 | 5 The BMC150 accelerometer kernel module provides an additional trigger,
|
| D | sysfs-bus-iio-gyro-bmg160 | 5 The BMG160 gyro kernel module provides an additional trigger,
|
| D | sysfs-bus-iio-accel-adxl372 | 5 The adxl372 accelerometer kernel module provides an additional trigger,
|
| /Documentation/core-api/irq/ |
| D | concepts.rst | 21 Architectures can assign additional meaning to the IRQ numbers, and
24 assigning this kind of additional meaning.
|
| /Documentation/networking/device_drivers/ethernet/intel/ |
| D | igbvf.rst | 13 - Additional Configurations
28 Instructions on updating ethtool can be found in the section Additional
41 Additional Features and Configurations
|
| /Documentation/admin-guide/cifs/ |
| D | todo.rst | 33 e) Additional use cases can be optimized to use "compounding" (e.g.
94 v) Additional testing of POSIX Extensions for SMB3.1.1
98 x) Support for additional authentication options (e.g. IAKERB, peer-to-peer
119 3) Additional performance testing and optimization using iozone and similar -
127 against Windows, Samba and Azure currently - to add additional tests and
|
| /Documentation/arch/riscv/ |
| D | uabi.rst | 20 #. Additional standard extensions (starting with 'Z') will be sorted after
23 #. For additional standard extensions, the first letter following the 'Z'
55 has the described capability. Additional kernel support or policy changes may be
|
| /Documentation/input/devices/ |
| D | appletouch.rst | 20 Frank Arnold for further improvements, and Alex Harper for some additional
32 will give additional functionalities, like acceleration, scrolling, 2 finger
37 example). For additional configuration, see the synaptics driver documentation::
|
| /Documentation/mm/ |
| D | remap_file_pages.rst | 9 require the kernel to create additional VMA (Virtual Memory Area) data
30 vm.max_map_count limit more easily due to additional VMAs. See comment for
|
| /Documentation/timers/ |
| D | hpet.rst | 11 additional hardware to support periodic interrupts. The comparators are
16 comparators are additional interrupt sources with no particular system
|
| /Documentation/devicetree/bindings/powerpc/4xx/ |
| D | cpm.txt | 36 If they are the same, the additional
39 refresh mode and any additional power
|
| /Documentation/devicetree/bindings/phy/ |
| D | phy-bindings.txt | 30 In order to differentiate between these 2 PHYs, an additional specifier should be
71 device defined previously. Note that the phy handle has an additional specifier
|
| /Documentation/driver-api/acpi/ |
| D | scan_handlers.rst | 29 appropriate data, but some of them require additional handling after they have
36 Those additional configuration tasks usually depend on the type of the hardware
60 for carrying out any additional configuration tasks related to it. It also will
|
| /Documentation/devicetree/bindings/net/ |
| D | socfpga-dwmac.txt | 6 The device node has additional properties:
29 This device node has additional phandle dependency, the sgmii converter:
|
| /Documentation/devicetree/bindings/iommu/ |
| D | ti,omap-iommu.txt | 13 and needs no additional data in the pargs specifier. Please
24 syscon node that contains the additional control
|
| /Documentation/hwmon/ |
| D | hwmon-kernel-api.rst | 17 For additional guidelines on how to write and improve hwmon drivers, please
92 `const struct attribute_group **extra_groups` Null-terminated list of additional non-standard
323 Only additional non-standard sysfs attributes need to be provided.
330 attribute has no additional context. However, in many cases there will be
331 additional information such as a sensor index which will need to be passed
335 which need such additional context information. SENSOR_DEVICE_ATTR requires
336 one additional argument, SENSOR_DEVICE_ATTR_2 requires two.
|
| /Documentation/devicetree/bindings/interrupt-controller/ |
| D | msi.txt | 10 potentially including additional information.
71 must be described with additional properties.
74 additional properties to describe the relationship between devices on the bus
|
| /Documentation/trace/ |
| D | sys-t.rst | 34 configfs gets a few additional attributes, which determine per-source
51 do_len switches on/off the additional "payload length" field in the
|
| /Documentation/devicetree/bindings/display/bridge/ |
| D | lontium,lt9211.yaml | 47 Additional MIPI port-2 for MIPI input or LVDS port-2
60 Additional MIPI port-2 for MIPI output or LVDS port-2
|
| /Documentation/devicetree/bindings/ata/ |
| D | sata_highbank.yaml | 32 Indicates the number of additional clock cycles to transmit before
38 Indicates the number of additional clock cycles to transmit after
|
12345678910>>...32