Searched full:band (Results 1 – 25 of 96) sorted by relevance
1234
| /Documentation/devicetree/bindings/net/wireless/ |
| D | marvell,sd8787.yaml | 39 description: Calibration data for the 2GHz band.
44 description: Calibration data for sub-band 0 in the 5GHz band.
49 description: Calibration data for sub-band 1 in the 5GHz band.
54 description: Calibration data for sub-band 2 in the 5GHz band.
59 description: Calibration data for sub-band 3 in the 5GHz band.
|
| D | ieee80211.yaml | 26 chipset supports a wide wireless band but it is limited to some part of
28 can be tri-band wireless router with two identical chipsets used for two
|
| /Documentation/userspace-api/media/rc/ |
| D | lirc-set-wideband-receiver.rst | 13 LIRC_SET_WIDEBAND_RECEIVER - enable wide band receiver.
35 Some receivers are equipped with special wide band receiver which is
39 This might be useful of receivers that have otherwise narrow band receiver
40 that prevents them to be used with some remotes. Wide band receiver might
46 Wide band receiver might be implicitly enabled if you enable
48 carrier reports. Trying to disable wide band receiver while carrier
|
| /Documentation/devicetree/bindings/net/dsa/ |
| D | mscc,ocelot.yaml | 114 managed = "in-band-status";
121 managed = "in-band-status";
128 managed = "in-band-status";
135 managed = "in-band-status";
183 managed = "in-band-status";
190 managed = "in-band-status";
197 managed = "in-band-status";
204 managed = "in-band-status";
211 managed = "in-band-status";
218 managed = "in-band-status";
[all …]
|
| /Documentation/devicetree/bindings/sound/ |
| D | nvidia,tegra210-mbdrc.yaml | 10 The Multi Band Dynamic Range Compressor (MBDRC) is part of Output
13 single full band or a dual band or a multi band dynamic processor.
|
| /Documentation/userspace-api/media/v4l/ |
| D | vidioc-enum-freq-bands.rst | 70 - Identifies the frequency band, set by the application.
74 frequency band, see :ref:`tuner-capability`. The
83 of 62.5 Hz, for this frequency band. A 1 Hz unit is used when the
89 units of 62.5 Hz, for this frequency band. A 1 Hz unit is used
94 band. See :ref:`band-modulation`.
98 Currently only one modulation system per frequency band
115 .. flat-table:: Band Modulation Systems
|
| D | vidioc-s-hw-freq-seek.rst | 42 to tell the driver to search a specific band. If the struct
50 current frequency of the tuner does not fall within the selected band it
51 will be clamped to fit in the band before the seek is started.
96 - If non-zero, the lowest tunable frequency of the band to search in
105 - If non-zero, the highest tunable frequency of the band to search
|
| /Documentation/userspace-api/media/drivers/ |
| D | max2175.rst | 26 The high-side/low-side (HSLS) control of the tuner for a given band.
52 - This configures FM band with a sample rate of 0.512 million
55 - This configures VHF band with a sample rate of 2.048 million
60 - This configures FM band with a sample rate of 0.7441875 million
63 - This configures FM band with a sample rate of 0.372 million
|
| /Documentation/networking/ |
| D | multiqueue.rst | 40 associated with the band is not stopped prior to dequeuing a packet.
44 will be queued to the band associated with the hardware queue.
58 queues, the band mapping would look like::
60 band 0 => queue 0
61 band 1 => queue 1
62 band 2 => queue 2
63 band 3 => queue 3
|
| D | sfp-phylink.rst | 35 3. In-band mode
37 In-band mode is used with 802.3z, SGMII and similar interface modes,
38 and we are expecting to use and honor the in-band negotiation or
50 does not use in-band SGMII signalling. The PHY is expected to follow
58 managed = "in-band-status";
63 uses in-band mode, where results from the PHY's negotiation are passed
197 It is important that if in-band negotiation is used,
199 in-band negotiation from completing, since these functions are called
200 when the in-band link state changes - otherwise the link will never
212 using. This is particularly important for in-band negotiation
[all …]
|
| /Documentation/driver-api/ |
| D | wbrf.rst | 4 WBRF - Wifi Band RFI Mitigations
61 2. On using some frequency band, call `acpi_amd_wbrf_add_remove` with 'add'
63 3. Or on stopping using some frequency band, call
70 of frequency band change(add or remove) from other producers.
74 4. On receiving a notification for frequency band change, run
|
| /Documentation/userspace-api/media/dvb/ |
| D | fe-set-tone.rst | 38 to send a 22kHz tone in order to select between high/low band on some
39 dual-band LNBf. It is also used to send signals to DiSEqC equipment, but
44 capability of selecting the band. So, it is recommended that applications
|
| /Documentation/devicetree/bindings/net/ |
| D | btusb.txt | 23 that shall be used for out-of-band wake-on-bt. Driver will
26 platform out of band. During system resume, the irq will be
31 Following example uses irq pin number 3 of gpio0 for out of band wake-on-bt:
|
| D | microchip,sparx5-switch.yaml | 169 managed = "in-band-status";
178 managed = "in-band-status";
187 managed = "in-band-status";
196 managed = "in-band-status";
|
| D | fsl,qoriq-mc-dpmac.yaml | 53 managed = "in-band-status";
|
| /Documentation/devicetree/bindings/iio/frequency/ |
| D | adi,admv4420.yaml | 7 title: ADMV4420 K Band Downconverter
15 for next generation K band satellite communications
|
| D | adi,admv1013.yaml | 68 Mixer Chip Band Gap Circuit voltage regulator.
72 VGA Chip Band Gap Circuit voltage regulator.
|
| /Documentation/devicetree/bindings/thermal/ |
| D | ti_soc_thermal.txt | 4 and a temperature sensor feature that are gathered in the band
5 gap voltage and temperature sensor (VBGAPTS) module. The band
|
| /Documentation/ABI/stable/ |
| D | sysfs-class-bluetooth | 8 (e.g., UART/USB), and can also be done through an out-of-band
|
| /Documentation/devicetree/bindings/mailbox/ |
| D | arm,mhuv3.yaml | 58 Optionally, data may be transmitted through an out-of-band shared memory
78 Optionally, data may be transmitted through an out-of-band shared memory
80 mechanism which carries also a pointer to such out-of-band data, but this
89 - Transfers which have in-band payload.
97 Optionally, additional data may be transmitted through an out-of-band shared
|
| /Documentation/devicetree/bindings/ipmi/ |
| D | aspeed,ast2400-ibt-bmc.txt | 5 perform in-band IPMI communication with their host.
|
| D | npcm7xx-kcs-bmc.txt | 5 used to perform in-band IPMI communication with their host.
|
| /Documentation/admin-guide/media/ |
| D | si470x.rst | 38 - Si4707: Dedicated weather band radio receiver with SAME decoder, RDS Support
133 (0444) are not updated, even if space, band and de are changed using private
142 When timed out or band limit is reached, hw_freq_seek returns -EAGAIN.
|
| /Documentation/devicetree/bindings/mtd/ |
| D | raw-nand-chip.yaml | 64 it as the device ages. Otherwise, the out-of-band area of a
77 only the in-band area is used by the upper layers, and you
|
| /Documentation/PCI/ |
| D | boot-interrupts.rst | 17 in-band interrupt mechanism was traditionally necessary for systems that
20 protocol describes this in-band legacy wire-interrupt INTx mechanism for
29 When in-band legacy INTx messages are forwarded to the PCH, they in turn
|
1234