Searched full:factory (Results 1 – 25 of 35) sorted by relevance
12
| /Documentation/input/devices/ |
| D | edt-ft5x06.rst | 40 allows switching the sensor between "factory mode" and "operation
41 mode" by writing "1" or "0" to it. In factory mode (1) it is
42 possible to get the raw data from the sensor. Note that in factory
52 Note that reading raw_data gives a I/O error when the device is not in factory
|
| /Documentation/devicetree/bindings/clock/ |
| D | silabs,si570.txt | 19 - factory-fout: Factory set default frequency. This frequency is part specific.
40 factory-fout = <156250000>;
|
| D | clps711x-clock.txt | 6 - startup-frequency: Factory set CPU startup frequency in HZ.
|
| /Documentation/devicetree/bindings/nvmem/ |
| D | st,stm32-romem.yaml | 7 title: STMicroelectronics STM32 Factory-programmed data
10 This represents STM32 Factory-programmed read only non-volatile area: locked
42 This property explicits a factory programmed area that both secure
|
| D | apple,efuses.yaml | 10 Apple SoCs such as the M1 contain factory-programmed eFuses used to e.g. store
|
| /Documentation/devicetree/bindings/mtd/ |
| D | mtd.yaml | 59 pre-programmed by the factory. Some flashes might provide both.
65 - factory-otp
96 compatible = "factory-otp";
|
| /Documentation/misc-devices/ |
| D | ad525x_dpot.rst | 9 settings. Access to the factory programmed tolerance is also provided, but
23 The tolerance files are the read-only factory programmed tolerance settings
|
| /Documentation/ABI/testing/ |
| D | sysfs-driver-tegra-fuse | 6 data programmed at the factory. The data is laid out in 32bit
|
| D | sysfs-class-rc-nuvoton | 13 factory default on each boot. On such systems store the
|
| D | sysfs-bus-iio-chemical-sunrise-co2 | 6 Writing '1' triggers a 'Factory' calibration cycle.
|
| D | sysfs-class-power-wilco | 24 On Wilco device this mode is pre-configured in the factory
|
| D | sysfs-class-cxl | 210 Will return "user" or "factory" depending on the image loaded
219 Valid entries are "none", "user", and "factory".
225 "user" and "factory" means PERST will cause either the user or
226 user or factory image to be loaded.
|
| D | sysfs-firmware-gsmi | 42 "factory defaults". Callers should assume that
|
| D | sysfs-class-firmware-attributes | 373 - 'factory' (Default factory settings configuration profile)
379 # echo "factory" > /sys/class/firmware-attributes/*/device/attributes/reset_bios
381 builtinsafe lastknowngood [factory] custom
|
| D | sysfs-bus-i2c-devices-turris-omnia-mcu | 97 Description: (RO) Contains the selected factory reset level, determined by
|
| /Documentation/devicetree/bindings/power/supply/ |
| D | battery.yaml | 84 factory-internal-resistance-micro-ohms:
85 description: battery factory internal resistance
161 factory-internal-resistance-micro-ohms = <250000>;
|
| /Documentation/hwmon/ |
| D | mcp3021.rst | 38 factory for additional address options).
|
| /Documentation/devicetree/bindings/sound/ |
| D | maxim,max98390.yaml | 27 description: This is r0 calibration data which was measured in factory mode.
|
| D | rt1011.txt | 29 u32. This is r0 calibration data which was measured in factory mode.
|
| /Documentation/devicetree/bindings/reset/ |
| D | ti,tps380x-reset.yaml | 16 reset input (MR). The RESET output remains asserted for the factory
|
| /Documentation/devicetree/bindings/display/panel/ |
| D | olimex,lcd-olinuxino.yaml | 26 The above chips share same I2C bus. The EEPROM is factory preprogrammed with
|
| /Documentation/driver-api/gpio/ |
| D | using-gpio.rst | 23 factory lines, maker community projects, workshop specimen, production tools,
|
| /Documentation/devicetree/bindings/mfd/ |
| D | ti,tps65086.yaml | 63 Set this if the regulator is factory set with a 25mv step voltage
|
| /Documentation/scsi/ |
| D | BusLogic.rst | 301 FlashPoint Host Adapters ship with their configuration set to "Factory
322 When configured to factory default settings, the BT-948/958/958D will only
338 this configuration option, but the factory default setting is "Primary".
358 factory default settings of the BT-948/958/958D enumerate the host adapters
371 The BT-948/958/958D ship with their configuration set to "Factory Default"
|
| /Documentation/devicetree/bindings/mtd/partitions/ |
| D | fixed-partitions.yaml | 180 label = "Factory";
|
12