Searched full:higher (Results 1 – 25 of 383) sorted by relevance
12345678910>>...16
| /Documentation/userspace-api/media/dvb/ |
| D | fe-enable-high-lnb-voltage.rst | 13 FE_ENABLE_HIGH_LNB_VOLTAGE - Select output DC level between normal LNBf voltages or higher LNBf - v…
33 - >0 - enables slightly higher voltages instead of 13/18V, in order
39 Select output DC level between normal LNBf voltages or higher LNBf
40 voltages between 0 (normal) or a value grater than 0 for higher
|
| /Documentation/scheduler/ |
| D | sched-debug.rst | 33 the higher the "scan size", the higher the scan rate.
35 Higher scan rates incur higher system overhead as page faults must be
36 trapped and potentially data must be migrated. However, the higher the scan
|
| /Documentation/tools/rtla/ |
| D | common_timerlat_options.rst | 14 Stop trace if the *IRQ* latency is higher than the argument in us.
18 Stop trace if the *Thread* latency is higher than the argument in us.
22 Save the stack trace at the *IRQ* if a *Thread* latency is higher than the
|
| D | common_osnoise_options.rst | 16 Stop the trace if a single sample is higher than the argument in microseconds.
21 Stop the trace if the total sample is higher than the argument in microseconds.
|
| /Documentation/devicetree/bindings/display/ |
| D | solomon,ssd1307fb.yaml | 85 the higher, the higher the capacitance of the OLED's pixels is.
99 Clock frequency, higher value means higher frequency.
|
| /Documentation/hwmon/ |
| D | nct6775.rst | 115 configuration. An alarm is triggered when the temperature gets higher than
207 speed increases (if temperature is higher that desired) or decreases (if
252 points should be set to higher temperatures and higher pwm values to achieve
253 higher fan speeds with increasing temperature. The last data point reflects
|
| D | adt7462.rst | 65 - point2: Set the pwm speed at a higher temperature bound.
67 The ADT7462 will scale the pwm between the lower and higher pwm speed when
|
| D | adt7470.rst | 64 - point2: Set the pwm speed at a higher temperature bound.
66 The ADT7470 will scale the pwm between the lower and higher pwm speed when
|
| D | w83627ehf.rst | 93 configurable. temp4 and higher attributes are only reported if its temperature
99 degC for temp1 and 0.5 degC for temp2 and temp3. For temp4 and higher,
101 An alarm is triggered when the temperature gets higher than high limit;
181 fan speed increases (temp is higher) or decreases if lower than desired.
|
| /Documentation/devicetree/bindings/regulator/ |
| D | nvidia,tegra-regulators-coupling.txt | 13 and they both shall be higher than the CPU voltage by at least 120mV.
20 voltage shall be higher than the CPU by N mV, where N depends on the CPU
|
| /Documentation/ABI/testing/ |
| D | sysfs-bus-iio-adc-mt6360 | 13 higher measure range(1~22mV)
20 Indicated MT6360 VBUS ADC with higher accuracy(+-30mA)
|
| D | sysfs-driver-xen-blkfront | 8 is 32 - higher value means more potential throughput but more
|
| D | sysfs-kernel-mm-memory-tiers | 21 A smaller value of N implies a higher (faster) memory tier in the
|
| D | sysfs-devices-power_state | 17 higher-power (lower-number) states may also be ON because of
|
| D | sysfs-platform-hidma-mgmt | 64 Choosing a higher number gives better performance but
85 Choosing a higher number gives better performance but
|
| /Documentation/devicetree/bindings/display/bridge/ |
| D | lontium,lt9211.yaml | 49 port-1 to drive higher resolution displays
62 port-1 to drive higher resolution displays.
|
| /Documentation/devicetree/bindings/iio/proximity/ |
| D | semtech,sx9360.yaml | 43 "measurement". Higher the number, higher the resolution.
|
| /Documentation/devicetree/bindings/power/supply/ |
| D | mediatek,mt6370-charger.yaml | 50 VBUS voltage with lower accuracy (+-75mV) but higher measure
53 VBUS voltage with higher accuracy (+-30mV) but lower measure
|
| /Documentation/filesystems/ |
| D | ecryptfs.rst | 28 1.0 or higher), obtainable from
79 then behavior is undefined. Do not run eCryptfs in higher verbosity
|
| /Documentation/process/ |
| D | 8.Conclusion.rst | 69 kernel. Getting code into the mainline is the key to higher code quality,
70 lower maintenance and distribution costs, a higher level of influence over
|
| /Documentation/admin-guide/mm/ |
| D | numaperf.rst | 104 slower performing memory cached by a smaller higher performing memory. The
107 higher performing memory to transparently cache access to progressively
111 hierarchy. Each increasing cache level provides higher performing
118 level memory, so the higher numbered cache level corresponds to memory
|
| /Documentation/driver-api/80211/ |
| D | introduction.rst | 13 higher-level overview.
|
| /Documentation/devicetree/bindings/thermal/ |
| D | imx-thermal.yaml | 28 will be triggered when temperature is higher than high threshold,
31 threshold, IRQ_LOW will be triggered, when temperature is higher
|
| /Documentation/block/ |
| D | bfq-iosched.rst | 109 Higher speed for code-development tasks
120 On hard disks, BFQ achieves up to 30% higher throughput than CFQ, and
121 up to 150% higher throughput than DEADLINE and NOOP, with all the
260 receive a higher fraction of the device throughput.
274 got access to the device, the higher the throughput is.
286 higher in this common scenario.
290 higher-priority queues. Among queues in the same class, the
489 reached a higher throughput by setting max_budget explicitly, i.e., by
490 setting max_budget to a higher value than 0. In particular, they have
491 set max_budget to higher values than those to which BFQ would have set
[all …]
|
| /Documentation/locking/ |
| D | rt-mutex-design.rst | 24 Priority inversion is when a lower priority process executes while a higher
38 meantime, B executes, and since B is of a higher priority than C, it preempts C,
39 but by doing so, it is in fact preempting A which is a higher priority process.
173 also call it the Top of the chain) must be equal to or higher in priority
360 pi waiter to its own normal/deadline priority and take the higher one.
367 higher the priority. A "prio" of 5 is of higher priority than a
371 or decrease the priority of the task. In the case that a higher priority
373 would increase/boost the task's priority. But if a higher priority task
|
12345678910>>...16