Searched full:initially (Results 1 – 25 of 87) sorted by relevance
1234
| /Documentation/driver-api/ |
| D | wbrf.rst | 38 Although initially used by for wifi + dGPU use cases, the ACPI interface
71 3. Call the `amd_wbrf_retrieve_freq_band` initially to retrieve
|
| /Documentation/ABI/testing/ |
| D | sysfs-bus-counter | 94 The output signal is initially low, and will remain low
100 The output signal is initially high. The output signal
109 The output signal is initially high. When the counter
116 The output signal is initially high.
135 The output signal is initially high. When the count
141 The output signal is initially high. Counting is started
|
| D | sysfs-bus-vdpa | 6 to a driver after the creation. It initially contains 1, which
|
| /Documentation/devicetree/bindings/iommu/ |
| D | pkvm,pviommu.yaml | 15 pvIOMMU was initially developed for protected KVM (pKVM), but it has no
|
| /Documentation/devicetree/bindings/power/reset/ |
| D | gpio-poweroff.yaml | 34 Initially configure the GPIO line as an input. Only reconfigure
|
| /Documentation/scheduler/ |
| D | sched-debug.rst | 47 initially forks.
|
| D | sched-domains.rst | 48 Initially, sched_balance_rq() finds the busiest group in the current sched domain.
|
| /Documentation/userspace-api/media/v4l/ |
| D | planar-apis.rst | 15 Initially, V4L2 API did not support multi-planar buffers and a set of
|
| /Documentation/gpu/rfc/ |
| D | i915_scheduler.rst | 30 * Initially only for GuC submission but execlists can be supported if
131 execbuf2 IOCTL can be called submitting N BBs in a single IOCTL. Initially only
|
| /Documentation/misc-devices/ |
| D | c2port.rst | 61 Initially the C2port access is disabled since you hardware may have
|
| /Documentation/networking/ |
| D | netif-msg.rst | 34 Initially this message level variable was uniquely named in each driver
|
| D | cdc_mbim.rst | 169 network device of the "wwan" type. This network device is initially
272 driver. It is initially mapped to untagged frames on the wwanY
|
| /Documentation/i2c/ |
| D | i2c-address-translators.rst | 80 as they were initially
|
| /Documentation/filesystems/ |
| D | ocfs2-online-filecheck.rst | 25 checking/fixing is at the file level, initially for regular files and eventually
|
| D | files.rst | 30 which the actual fd table is accessed. Initially the
|
| D | adfs.rst | 101 file type information, a file naming convention was devised (initially
|
| /Documentation/virt/kvm/s390/ |
| D | s390-diag.rst | 110 Forwarding the DIAGNOSE 0x9c initially sent by the guest to yield to
|
| /Documentation/trace/rv/ |
| D | da_monitor_instrumentation.rst | 81 Initially, the *model* is placed in the initial state. However, the *system*
|
| /Documentation/device-mapper/ |
| D | dm-bow.txt | 83 initially. A log entry is
|
| /Documentation/cpu-freq/ |
| D | cpufreq-stats.rst | 98 which the driver has provided the frequency table initially to the cpufreq core
|
| /Documentation/security/ |
| D | ipe.rst | 57 initially, passing the required integrity check. Then, on the page fault
252 this is the ``SYSTEM_TRUSTED_KEYRING``, a keyring that is initially
269 Initially, IPE's policy can have a policy_version that states the
|
| /Documentation/admin-guide/mm/ |
| D | idle_page_tracking.rst | 67 If the tool is run initially with the appropriate option, it will mark all the
|
| /Documentation/driver-api/nvdimm/ |
| D | security.rst | 47 security specification [2]. A key is initially acquired via the request_key()
|
| /Documentation/power/ |
| D | runtime_pm.rst | 241 initially disabled for all devices)
265 RPM_SUSPENDED, which means that each device is initially regarded by the
270 PM for it (invalid initially and when disable_depth is 0)
572 Initially, the runtime PM is disabled for all devices, which means that the
578 Thus, if the device is initially active (i.e. it is able to process I/O), its
877 length initially by calling pm_runtime_set_autosuspend_delay(), but after device
|
| /Documentation/admin-guide/media/ |
| D | vivid.rst | 348 The initially selected colorspace when you switch to the webcam input will be
378 The initially selected colorspace when you switch to the TV or S-Video input
417 The initially selected colorspace when you switch to the HDMI input or
462 The initially selected colorspace when you switch to the TV or S-Video input
473 The initially selected colorspace when you switch to the HDMI output or
1226 initially no looping takes place.
|
1234