Searched full:invert (Results 1 – 25 of 65) sorted by relevance
123
| /Documentation/devicetree/bindings/sound/ |
| D | audio-iio-aux.yaml | 31 snd-control-invert-range:
40 Invert the sound control value compared to the IIO channel raw value.
62 /* Invert CH1 and CH2 */
63 snd-control-invert-range = <0 1 1 0>;
|
| D | qcom,q6dsp-lpass-ports.yaml | 77 qcom,tdm-invert-sync:
81 TDM Invert the sync
83 1 = Invert
99 width in case of sample bit width is 24TDM Invert the sync.
120 - qcom,tdm-invert-sync
|
| D | cirrus,cs42l43.yaml | 120 cirrus,tip-invert:
134 debounced for. Note the falling edge is considered after the invert.
141 debounced for. Note the rising edge is considered after the invert.
150 cirrus,ring-invert:
164 debounced for. Note the falling edge is considered after the invert.
171 debounced for. Note the rising edge is considered after the invert.
|
| D | cs35l36.txt | 43 - cirrus,amp-pcm-inv : Boolean to determine Amplifier will invert incoming
46 - cirrus,imon-pol-inv : Boolean to determine Amplifier will invert the
49 - cirrus,vmon-pol-inv : Boolean to determine Amplifier will invert the
|
| D | everest,es8326.yaml | 61 Defined to invert the jack detection.
87 Bit(4) 1 means we invert the interrupt output.
|
| /Documentation/devicetree/bindings/iio/cdc/ |
| D | adi,ad7746.yaml | 38 adi,exca-output-invert:
50 adi,excb-output-invert:
72 adi,exca-output-invert;
74 adi,excb-output-invert;
|
| /Documentation/devicetree/bindings/clock/ti/ |
| D | autoidle.txt | 14 - ti,invert-autoidle-bit : autoidle is enabled by setting the bit to 0
25 ti,invert-autoidle-bit;
36 ti,invert-autoidle-bit;
|
| D | fixed-factor-clock.txt | 21 - ti,invert-autoidle-bit: autoidle is enabled by setting the bit to 0, see [2]
41 ti,invert-autoidle-bit;
|
| /Documentation/leds/ |
| D | ledtrig-oneshot.rst | 17 additional "invert" property specifies if the LED has to stay off (normal) or
36 echo 1 > invert # set led as normally-on, turn the led on
44 echo 0 > invert # set led as normally-off, turn the led off
|
| /Documentation/devicetree/bindings/pwm/ |
| D | nxp,pca9685-pwm.txt | 12 - invert (bool): boolean to enable inverted logic
25 invert;
|
| /Documentation/devicetree/bindings/display/ti/ |
| D | ti,omap2-dss.txt | 57 - ti,invert-polarity: invert the polarity of the video signal
|
| D | ti,omap3-dss.txt | 68 - ti,invert-polarity: invert the polarity of the video signal
|
| D | ti,omap4-dss.txt | 74 - ti,invert-polarity: invert the polarity of the video signal
|
| /Documentation/ABI/testing/ |
| D | sysfs-bus-iio-adc-envelope-detector | 24 The boolean invert attribute (0/1) should be set when the
27 from below in this case and will also invert the result.
|
| D | sysfs-bus-iio-dac-ad5766 | 12 inverted by default. Write "1" to invert dither.
|
| /Documentation/devicetree/bindings/display/ |
| D | cirrus,clps711x-fb.txt | 14 - cmap-invert : Invert the color levels (Optional).
|
| /Documentation/devicetree/bindings/display/samsung/ |
| D | samsung,fimd.yaml | 114 samsung,invert-vden:
119 samsung,invert-vclk:
184 samsung,invert-vden;
185 samsung,invert-vclk;
|
| /Documentation/sound/soc/ |
| D | codec.rst | 81 #define SOC_SINGLE(xname, reg, shift, mask, invert)
90 invert = the control is inverted
95 #define SOC_DOUBLE(xname, reg, shift_left, shift_right, mask, invert)
100 #define SOC_DOUBLE_R(xname, reg_left, reg_right, shift, mask, invert)
|
| /Documentation/devicetree/bindings/usb/ |
| D | fsl,usb2.yaml | 50 fsl,invert-drvvbus:
56 fsl,invert-pwr-fault:
|
| /Documentation/devicetree/bindings/phy/ |
| D | phy-miphy365x.txt | 36 - st,pcie-tx-pol-inv : Bool property to invert the polarity PCIe Tx (Txn/Txp)
37 - st,sata-tx-pol-inv : Bool property to invert the polarity SATA Tx (Txn/Txp)
|
| D | brcm,brcmstb-usb-phy.yaml | 64 description: Invert Port Power
70 description: Invert Over Current detection
|
| /Documentation/devicetree/bindings/extcon/ |
| D | wlf,arizona.yaml | 40 wlf,jd-invert:
42 Invert the polarity of the jack detection switch.
|
| /Documentation/devicetree/bindings/net/can/ |
| D | nxp,sja1000.yaml | 65 <0x01> : TX0 invert
69 <0x08> : TX1 invert
|
| /Documentation/devicetree/bindings/serial/ |
| D | fsl-imx-uart.yaml | 84 transmitted, and that the peripheral should invert its output using the
91 received, and that the peripheral should invert its input using the
|
| /Documentation/devicetree/bindings/input/ |
| D | azoteq,iqs7222.yaml | 459 azoteq,invert-enable:
999 azoteq,invert-enable;
1008 azoteq,invert-enable;
1017 azoteq,invert-enable;
1026 azoteq,invert-enable;
1035 azoteq,invert-enable;
1045 azoteq,invert-enable;
1054 azoteq,invert-enable;
1067 azoteq,invert-enable;
1080 azoteq,invert-enable;
[all …]
|
123