Searched full:inverted (Results 1 – 25 of 122) sorted by relevance
12345
| /Documentation/devicetree/bindings/input/touchscreen/ |
| D | brcm,iproc-touchscreen.txt | 59 - touchscreen-inverted-x: X axis is inverted (boolean)
60 - touchscreen-inverted-y: Y axis is inverted (boolean)
85 touchscreen-inverted-x;
86 touchscreen-inverted-y;
|
| D | imagis,ist3038c.yaml | 43 touchscreen-inverted-x: true
44 touchscreen-inverted-y: true
85 touchscreen-inverted-x;
86 touchscreen-inverted-y;
|
| D | melfas,mms114.yaml | 54 touchscreen-inverted-x: true
55 touchscreen-inverted-y: true
91 touchscreen-inverted-x;
92 touchscreen-inverted-y;
|
| D | eeti,exc3000.yaml | 35 touchscreen-inverted-x: true
36 touchscreen-inverted-y: true
61 touchscreen-inverted-x;
|
| D | bu21013.txt | 15 - touchscreen-inverted-x : General touchscreen binding, see [1].
16 - touchscreen-inverted-y : General touchscreen binding, see [1].
41 touchscreen-inverted-y;
|
| D | ilitek_ts_i2c.yaml | 47 touchscreen-inverted-x: true
48 touchscreen-inverted-y: true
73 touchscreen-inverted-y;
|
| D | touchscreen.yaml | 65 touchscreen-inverted-x:
66 description: X axis is inverted
69 touchscreen-inverted-y:
70 description: Y axis is inverted
|
| D | raspberrypi,firmware-ts.txt | 11 - touchscreen-inverted-x: See touchscreen.txt
12 - touchscreen-inverted-y: See touchscreen.txt
|
| D | zet6223.txt | 15 - touchscreen-inverted-x : See touchscreen.txt
16 - touchscreen-inverted-y : See touchscreen.txt
|
| D | eeti.txt | 16 - touchscreen-inverted-x
17 - touchscreen-inverted-y
|
| D | hynitron,cstxxx.yaml | 35 touchscreen-inverted-x: true
36 touchscreen-inverted-y: true
|
| D | elan,elants_i2c.yaml | 45 touchscreen-inverted-x: true
46 touchscreen-inverted-y: true
|
| D | himax,hx83112b.yaml | 30 touchscreen-inverted-x: true
31 touchscreen-inverted-y: true
|
| D | azoteq,iqs5xx.yaml | 42 touchscreen-inverted-x: true
43 touchscreen-inverted-y: true
|
| /Documentation/devicetree/bindings/mmc/ |
| D | vt8500-sdmmc.txt | 11 - sdon-inverted: SD_ON bit is inverted on the controller
21 sdon-inverted;
|
| D | atmel-hsmci.txt | 44 - cd-inverted: invert the value of external card detect gpio line
53 cd-inverted;
67 cd-inverted;
|
| D | fsl,esdhc.yaml | 47 sdhci,wp-inverted:
52 inverted write-protect state; New devices should use the generic
53 "wp-inverted" property.
|
| D | mmc-controller.yaml | 54 # of the "normal" and "inverted" line levels. We choose to follow
56 # low." Therefore, using the "cd-inverted" property means, that the
58 # inserted. Similar logic applies to the "wp-inverted" property.
63 # using *-inverted properties. GPIO polarity can also be specified
68 # respective *-inverted property property results in a
71 wp-inverted:
74 The Write Protect line polarity is inverted.
76 cd-inverted:
79 The CD line polarity is inverted.
|
| /Documentation/devicetree/bindings/sound/ |
| D | rt5651.txt | 25 - realtek,jack-detect-not-inverted
26 bool. Normal jack-detect switches give an inverted (active-low) signal,
28 inverted.
|
| D | audio-iio-aux.yaml | 35 inverted
41 - 1: The related sound control value is inverted meaning that the
45 - 0: The related sound control value is not inverted meaning that the
|
| D | rt5640.txt | 48 - realtek,jack-detect-not-inverted
49 bool. Normal jack-detect switches give an inverted signal, set this bool
50 in the rare case you've a jack-detect switch which is not inverted.
|
| /Documentation/devicetree/bindings/net/ |
| D | motorcomm,yt8xxx.yaml | 92 Useful if you want to use tx-clk-xxxx-inverted to adj the delay of tx clk.
95 motorcomm,tx-clk-10-inverted:
97 Use original or inverted RGMII Transmit PHY Clock to drive the RGMII
101 motorcomm,tx-clk-100-inverted:
103 Use original or inverted RGMII Transmit PHY Clock to drive the RGMII
107 motorcomm,tx-clk-1000-inverted:
109 Use original or inverted RGMII Transmit PHY Clock to drive the RGMII
|
| /Documentation/devicetree/bindings/clock/ |
| D | ti,lmk04832.yaml | 122 CMOS (Off/Inverted) 0x0a
124 CMOS (Inverted/Inverted) 0x0c
125 CMOS (Inverted/Normal) 0x0d
126 CMOS (Normal/Inverted) 0x0e
|
| /Documentation/userspace-api/media/rc/ |
| D | rc-protos.rst | 55 - 6 (inverted)
78 where there the second stop bit is the 6th command bit, but inverted.
80 schemes. This bit is stored in bit 6 of the scancode, inverted. This is
182 The jvc protocol is much like nec, without the inverted values. It is
283 second time it is inverted. This is done for verification.
298 nec-32 does not send an inverted address or an inverted command; the
302 inverted value of the first, and also the last 8 bits must not be the
303 inverted value of the third 8 bit value.
334 their inverted versions, but these are not present in the scancodes.
399 (40ms) space between the normal and inverted values, and some IR receivers
|
| /Documentation/devicetree/bindings/media/i2c/ |
| D | tvp7002.txt | 22 1 = Inverted operation
28 1 = FID output polarity inverted
|
12345