Searched full:lsb (Results 1 – 25 of 75) sorted by relevance
123
| /Documentation/hwmon/ |
| D | ad7314.rst | 28 sensor with 1lsb = 0.25 degrees centigrade. The adt7301 and
29 adt7302 have 14 bit sensors with 1lsb = 0.03125 degrees centigrade.
|
| D | lm73.rst | 32 LSB: 0.25, 0.125, 0.0625, and 0.3125. Changing the resolution mode
41 (C/LSB) (msec) (msec)
87 resolution in degrees C per LSB.
|
| D | smsc47b397.rst | 42 and 0x61 (LSB). Currently we are using 0x480 for the HWM Base Address and
73 LSB MSB
83 Reading the tach LSB locks the tach MSB.
84 The LSB Must be read first.
89 The tach reading (TCount) is given by: (Tach MSB * 256) + (Tach LSB)
|
| D | max127.rst | 37 ADC range and LSB will be updated when the limit is changed.
42 ADC range and LSB will be updated when the limit is changed.
|
| /Documentation/devicetree/bindings/gpio/ |
| D | netxbig-gpio-ext.txt | 6 - addr-gpios: GPIOs representing the address register (LSB -> MSB).
7 - data-gpios: GPIOs representing the data register (LSB -> MSB).
|
| /Documentation/devicetree/bindings/iio/amplifiers/ |
| D | adi,hmc425a.yaml | 15 ADRF5750 2 dB LSB, 4-Bit, Silicon Digital Attenuator, 10 MHz to 60 GHz
18 HMC425A 0.5 dB LSB GaAs MMIC 6-BIT DIGITAL POSITIVE CONTROL ATTENUATOR, 2.2 - 8.0 GHz
21 HMC540S 1 dB LSB Silicon MMIC 4-Bit Digital Positive Control Attenuator, 0.1 - 8 GHz
|
| /Documentation/devicetree/bindings/sound/ |
| D | tdm-slot.txt | 23 for an active slot as default, and the default active bits are at the LSB of
27 number presents bit-0 (LSB), second presents bit-1, etc. Any non zero
|
| D | fsl,sai.yaml | 139 lsb-first:
141 Configures whether the LSB or the MSB is transmitted
143 the MSB is transmitted first as default, or the LSB
188 lsb-first;
|
| /Documentation/devicetree/bindings/rtc/ |
| D | maxim-ds1302.txt | 24 - spi-lsb-first : DS-1302 requires least significant bit first
43 spi-lsb-first;
|
| /Documentation/userspace-api/media/v4l/ |
| D | vidioc-g-sliced-vbi-cap.rst | 146 run-in and framing code, lsb first transmitted.
151 - Byte number 3 to 15 according to Figure 9 of ETS 300 231, lsb
157 - Two bytes in transmission order, including parity bit, lsb first
188 | | msb | lsb | msb | lsb |
|
| D | colorspaces-defs.rst | 145 - For the Hue, each LSB is two degrees.
148 LSB is roughly 1.41 degrees.
|
| /Documentation/devicetree/bindings/thermal/ |
| D | armada-thermal.txt | 26 to "control LSB/control 0" with size of 8 (current binding). All other
27 compatibles must point to "control LSB/control 0" with size of 8.
|
| /Documentation/devicetree/bindings/spi/ |
| D | icpdas-lp8841-spi-rtc.txt | 34 - spi-lsb-first: DS-1302 requires least significant bit first
51 spi-lsb-first;
|
| D | spi-peripheral-props.yaml | 37 spi-lsb-first:
40 The device requires the LSB first mode.
|
| /Documentation/ABI/testing/ |
| D | sysfs-bus-usb-devices-usbsevseg | 16 MSB 0x06; LSB 0x3F, and
20 MSB 0x08; LSB 0xFF.
|
| D | sysfs-driver-tegra-fuse | 7 words in LSB first format. Each bit represents a single value
|
| /Documentation/usb/ |
| D | misc_usbsevseg.rst | 20 MSB 0x06; LSB 0x3f
24 MSB 0x08; LSB 0xff
|
| /Documentation/devicetree/bindings/display/msm/ |
| D | mdp4.yaml | 60 qcom,lcdc-align-lsb:
63 Indication that LSB alignment should be used for LCDC.
|
| /Documentation/ABI/removed/ |
| D | devfs | 7 against the LSB, and can be replaced by using udev.
|
| /Documentation/input/devices/ |
| D | iforce-protocol.rst | 64 00 X-Axis lsb
66 02 Y-Axis lsb, or gas pedal for a wheel
84 03 Address of parameter block changed (lsb)
86 05 Address of second parameter block changed (lsb)
|
| /Documentation/devicetree/bindings/hwmon/ |
| D | nuvoton,nct6775.yaml | 36 active. LSB is TSI0, bit 1 is TSI1, etc.
|
| D | gpio-fan.yaml | 19 ordered MSB-->LSB.
|
| /Documentation/devicetree/bindings/dma/ |
| D | dma-common.yaml | 31 kernel. i.e. first channel corresponds to LSB.
|
| /Documentation/admin-guide/ |
| D | lcd-panel-cgram.rst | 10 illuminated pixel with LSB on the right. Lines are numbered from the
|
| /Documentation/driver-api/nfc/ |
| D | nfc-pn544.rst | 30 and third (LSB) bytes of the message. The maximum FW message length is
|
123