Searched full:mbit (Results 1 – 18 of 18) sorted by relevance
| /Documentation/usb/ |
| D | ehci.rst | 11 - "High Speed" 480 Mbit/sec (60 MByte/sec)
12 - "Full Speed" 12 Mbit/sec (1.5 MByte/sec)
13 - "Low Speed" 1.5 Mbit/sec
155 them. The 480 Mbit/sec "raw transfer rate" is obeyed by all devices,
168 approach the quoted 480 MBit/sec transfer rate.
|
| /Documentation/admin-guide/cgroup-v1/ |
| D | net_cls.rst | 36 tc class add dev eth0 parent 10: classid 10:1 htb rate 40mbit
|
| /Documentation/devicetree/bindings/net/ |
| D | wiznet,w5x00.txt | 3 This is a standalone 10/100 MBit Ethernet controller with SPI interface.
|
| D | microchip,enc28j60.txt | 3 This is a standalone 10 MBit ethernet controller with SPI interface.
|
| D | microchip,sparx5-switch.yaml | 101 description: Specifies bandwidth in Mbit/s allocated to the port.
|
| D | fsl,fman-dtsec.yaml | 15 10/100/1000 MBit/s speeds, and the 10-Gigabit Ethernet Media Access Controller
|
| D | cdns,macb.yaml | 44 - atmel,sama5d3-macb # 10/100Mbit IP on Atmel sama5d3 SoCs
|
| D | ethernet-controller.yaml | 46 Specifies maximum speed in Mbit/s supported by the device.
|
| /Documentation/networking/device_drivers/ethernet/ti/ |
| D | tlan.rst | 118 use the above options on a per adapter basis. To force a 100Mbit/HD
123 Now eth0 will use auto-neg and eth1 will be forced to 100Mbit/HD.
|
| D | cpsw.rst | 228 // Set rate for class A - 41 Mbit (tc0, txq0) using CBS Qdisc
238 // Set rate for class B - 21 Mbit (tc1, txq1) using CBS Qdisc:
451 // Set rate for class A - 41 Mbit (tc0, txq0) using CBS Qdisc for Eth0
460 // Set rate for class B - 21 Mbit (tc1, txq1) using CBS Qdisc for Eth0
510 // Set rate for class A - 31 Mbit (tc0, txq2) using CBS Qdisc for Eth1
520 // Set rate for class B - 11 Mbit (tc1, txq3) using CBS Qdisc for Eth1
|
| /Documentation/driver-api/ |
| D | hsi.rst | 13 (typically 8) and is capable of reaching speeds up to 200 Mbit/s.
|
| /Documentation/driver-api/media/drivers/ |
| D | dvb-usb.rst | 297 maximum bandwidth of about 5-6 MBit/s when connected to a USB2.0 hub.
299 DVB-T channel (which is about 16 MBit/s). Normally this is not a
|
| /Documentation/driver-api/usb/ |
| D | usb.rst | 16 USB 2.0 (480 MBit/s) busses just in case.
419 speed (480 MBit/sec) or just full speed (12 MBit/sec).* You should
778 1.5 Mbit/s for low speed USB
779 12 Mbit/s for full speed USB
780 480 Mbit/s for high speed USB (added for USB 2.0)
781 5000 Mbit/s for SuperSpeed USB (added for USB 3.0)
|
| /Documentation/ABI/stable/ |
| D | sysfs-bus-usb | 140 Mbit / second. IE one of 1.5 / 12 / 480 / 5000.
|
| /Documentation/networking/device_drivers/ethernet/neterion/ |
| D | s2io.rst | 180 device support ---> Ethernet (10000 Mbit) ---> S2IO 10Gbe Xframe NIC) to
|
| /Documentation/virt/uml/ |
| D | user_mode_linux_howto_v2.rst | 222 | tuntap | legacy | none | ~ 500Mbit |
224 | daemon | legacy | none | ~ 450Mbit |
226 | socket | legacy | none | ~ 450Mbit |
228 | ethertap | legacy | obsolete | ~ 500Mbit |
230 | vde | legacy | obsolete | ~ 500Mbit |
239 * All legacy transports are generally limited to ~600-700MBit and 0.05Mps.
|
| /Documentation/networking/ |
| D | oa-tc6-framework.rst | 10 The IEEE 802.3cg project defines two 10 Mbit/s PHYs operating over a
|
| D | can.rst | 1447 Example configuring 500 kbit/s arbitration bitrate and 4 Mbit/s data bitrate::
|