Searched full:mbps (Results 1 – 25 of 51) sorted by relevance
123
| /Documentation/ABI/testing/ |
| D | sysfs-class-led-trigger-netdev | 83 Signal the link speed state of 10Mbps of the named network device.
88 speed of 10MBps of the named network device.
91 Present only if the named network device supports 10Mbps link speed.
98 Signal the link speed state of 100Mbps of the named network device.
103 speed of 100Mbps of the named network device.
106 Present only if the named network device supports 100Mbps link speed.
113 Signal the link speed state of 1000Mbps of the named network device.
118 speed of 1000Mbps of the named network device.
121 Present only if the named network device supports 1000Mbps link speed.
128 Signal the link speed state of 2500Mbps of the named network device.
[all …]
|
| D | debugfs-driver-qat_telemetry | 58 bw_in PCIe, write bandwidth [Mbps]
59 bw_out PCIe, read bandwidth [Mbps]
132 bw_in PCIe, write bandwidth [Mbps]
133 bw_out PCIe, read bandwidth [Mbps]
|
| /Documentation/devicetree/bindings/phy/ |
| D | mscc,vsc7514-serdes.yaml | 22 There are two kinds of SerDes: SERDES1G supports 10/100Mbps in
23 half/full-duplex and 1000Mbps in full-duplex mode while SERDES6G supports
24 10/100Mbps in half/full-duplex and 1000/2500Mbps in full-duplex mode.
|
| D | microchip,sparx5-serdes.yaml | 34 * 100 Mbps (100BASE-FX)
44 * 100 Mbps (100BASE-FX)
|
| /Documentation/networking/device_drivers/ethernet/dlink/ |
| D | dl2k.rst | 215 10mbps_hd 10Mbps half duplex.
216 10mbps_fd 10Mbps full duplex.
217 100mbps_hd 100Mbps half duplex.
218 100mbps_fd 100Mbps full duplex.
219 1000mbps_fd 1000Mbps full duplex.
220 1000mbps_hd 1000Mbps half duplex.
222 1 10Mbps half duplex.
223 2 10Mbps full duplex.
224 3 100Mbps half duplex.
225 4 100Mbps full duplex.
[all …]
|
| /Documentation/scsi/ |
| D | ufs.rst | 41 - Support for Gear1 is mandatory (rate A: 1248Mbps, rate B: 1457.6Mbps)
42 - Support for Gear2 is optional (rate A: 2496Mbps, rate B: 2915.2Mbps)
46 - Gear3 (rate A: 4992Mbps, rate B: 5830.4Mbps)
|
| /Documentation/devicetree/bindings/net/ |
| D | renesas,ethertsn.yaml | 13 The RTSN device provides Ethernet network using a 10 Mbps, 100 Mbps, or 1
|
| D | opencores-ethoc.txt | 1 * OpenCores MAC 10/100 Mbps
|
| D | motorcomm,yt8xxx.yaml | 98 Transmit PHY Clock delay train configuration when speed is 10Mbps.
104 Transmit PHY Clock delay train configuration when speed is 100Mbps.
110 Transmit PHY Clock delay train configuration when speed is 1000Mbps.
|
| D | adi,adin1110.yaml | 23 10 Mbps single pair Ethernet (SPE).
|
| D | microchip,lan8650.yaml | 15 (MAC) module implements a 10 Mbps half duplex Ethernet MAC, compatible
|
| D | loongson,ls1c-emac.yaml | 17 - 10/100Mbps
|
| D | loongson,ls1b-gmac.yaml | 17 - Dual 10/100/1000Mbps GMAC controllers
|
| D | ti,dp83822.yaml | 14 The DP83822 is a low-power, single-port, 10/100 Mbps Ethernet PHY. It
|
| /Documentation/devicetree/bindings/media/i2c/ |
| D | st,st-mipid02.yaml | 17 CSI-2 first input port is a dual lane 800Mbps per lane whereas CSI-2
18 second input port is a single lane 800Mbps. Both ports support clock
|
| D | sony,imx274.yaml | 16 Mbps.
|
| D | st,st-vgxy61.yaml | 16 quad lanes 800Mbps per lane.
|
| D | maxim,max96712.yaml | 22 forward direction and 187.5Mbps in the reverse direction. In GMSL1 mode, the
|
| D | ovti,ov5675.yaml | 70 # Supports max data transfer of 900 Mbps per lane
|
| /Documentation/devicetree/bindings/input/touchscreen/ |
| D | cypress,cy8ctma340.yaml | 47 the device on the SPI bus. The throughput is maximum 2 Mbps so the
49 needs to be restricted to 2 Mbps.
|
| /Documentation/networking/device_drivers/ethernet/3com/ |
| D | vortex.rst | 33 - 3c590 Vortex 10Mbps
34 - 3c592 EISA 10Mbps Demon/Vortex
40 - 3c900 Boomerang 10Mbps Combo
41 - 3c900 Cyclone 10Mbps TPO
42 - 3c900 Cyclone 10Mbps Combo
43 - 3c900 Cyclone 10Mbps TPC
|
| /Documentation/devicetree/bindings/net/bluetooth/ |
| D | amlogic,w155s2-bt.yaml | 13 up to 4 Mbps.
|
| /Documentation/networking/dsa/ |
| D | lan9303.rst | 5 The LAN9303 is a three port 10/100 Mbps ethernet switch with integrated phys for
|
| /Documentation/networking/device_drivers/ethernet/intel/ |
| D | e1000.rst | 252 (Mbps). If this parameter is not specified or is set to 0 and the link
342 fiber interface board only links at 1000 Mbps full-duplex.
350 - If Speed = 1000, limited auto-negotiation is enabled and only 1000 Mbps
369 Speed (Mbps) N/A N/A 1000 N/A 100 100 10 10
422 - Using Jumbo frames at 10 or 100 Mbps is not supported and may result in
|
| /Documentation/networking/device_drivers/ethernet/ti/ |
| D | tlan.rst | 91 To force a 10Mbps Half-Duplex link do "insmod tlan.o speed=10
115 ether=0,0,0x12,0,eth0 will force link to 100Mbps Half-Duplex.
|
123