Searched full:multiplier (Results 1 – 25 of 40) sorted by relevance
12
| /Documentation/devicetree/bindings/clock/ |
| D | keystone-pll.txt | 1 Binding for keystone PLLs. The main PLL IP typically has a multiplier,
15 - reg - pll control0 and pll multiplier registers
16 - reg-names : control, multiplier and post-divider. The multiplier and
27 reg-names = "control", "multiplier", "post-divider";
|
| D | moxa,moxart-clock.txt | 8 by reading registers holding multiplier and divisor information.
|
| D | ti,cdce706.txt | 2 synthesizer/multiplier/divider.
|
| D | fixed-factor-clock.yaml | 39 description: Fixed multiplier
|
| D | cirrus,cs2000-cp.yaml | 7 title: CIRRUS LOGIC Fractional-N Clock Synthesizer & Clock Multiplier
|
| /Documentation/devicetree/bindings/dma/ |
| D | img-mdc-dma.txt | 13 - img,max-burst-multiplier: Must be the maximum supported burst size multiplier.
46 img,max-burst-multiplier = <16>;
|
| /Documentation/ABI/testing/ |
| D | configfs-usb-gadget-ecm | 11 - queue length multiplier for high and
|
| D | configfs-usb-gadget-ncm | 9 qmult - queue length multiplier for high and
|
| D | configfs-usb-gadget-eem | 10 qmult queue length multiplier for high and
|
| D | configfs-usb-gadget-subset | 10 qmult queue length multiplier for high and
|
| D | sysfs-driver-w1_ds28e17 | 18 Description: When written, this file sets the multiplier used to calculate
|
| D | configfs-usb-gadget-rndis | 10 qmult queue length multiplier for high and
|
| /Documentation/devicetree/bindings/iio/light/ |
| D | amstaos,tsl2563.yaml | 27 description: Multiplier for gain compensation
|
| /Documentation/devicetree/bindings/clock/ti/ |
| D | ti,clksel.yaml | 14 cases also has divider, multiplier and gate bits.
|
| D | fixed-factor-clock.txt | 13 - ti,clock-mult: fixed multiplier.
|
| D | mux.txt | 6 gate or adjust the parent rate via a divider or multiplier.
|
| D | dpll.txt | 41 "mult-div1" - contains the multiplier / divider register base address
|
| /Documentation/arch/nios2/ |
| D | nios2.rst | 19 with MMU and hardware multiplier enabled.
|
| /Documentation/devicetree/bindings/iio/afe/ |
| D | current-sense-amplifier.yaml | 32 description: Amplifier gain multiplier. The default is <1>.
|
| /Documentation/leds/ |
| D | leds-sc27xx.rst | 24 a multiplier of 125, like 125ms, 250ms, 375ms, 500ms ... 31875ms.
|
| /Documentation/hwmon/ |
| D | ftsteutates.rst | 30 The 4 voltages require a board-specific multiplier, since the BMC can
|
| D | ina209.rst | 27 calibration multiplier to scale the displayed current and power values.
|
| /Documentation/devicetree/bindings/ata/ |
| D | sata-common.yaml | 54 each port can have a Port Multiplier attached thus allowing to
|
| /Documentation/devicetree/bindings/display/bridge/ |
| D | ti,tfp410.yaml | 27 through the DK[3:1] pins. The de-skew multiplier is computed as
|
| /Documentation/w1/slaves/ |
| D | w1_ds28e17.rst | 52 DS28E17 devices. It is a multiplier used on the calculation of the busy
|
12