Searched full:perst (Results 1 – 25 of 25) sorted by relevance
| /Documentation/devicetree/bindings/pci/ |
| D | qcom,pcie-ep.yaml | 53 qcom,perst-regs:
55 offsets within syscon for Perst enable and Perst separation
61 - description: Perst enable offset
62 - description: Perst separation enable offset
79 description: GPIO used as PERST# input signal
266 qcom,perst-regs = <&tcsr 0xb258 0xb270>;
|
| D | starfive,jh7110-pcie.yaml | 56 perst-gpios:
57 description: GPIO controlled connection to PERST# signal
111 perst-gpios = <&gpios 26 GPIO_ACTIVE_LOW>;
|
| D | qcom,pcie-common.yaml | 73 perst-gpios:
74 description: GPIO controlled connection to PERST# signal
|
| D | hisilicon-histb-pcie.txt | 36 - reset-gpios: The gpio to generate PCIe PERST# assert and deassert signal.
|
| D | snps,dw-pcie-common.yaml | 208 Reference to the GPIO-controlled PERST# signal. It is used to reset all
214 Reference to the GPIO-controlled PERST# signal. It is used to reset all
|
| D | pci.txt | 28 If present this property specifies PERST# GPIO. Host drivers can parse the
|
| D | qcom,pcie.yaml | 107 perst-gpios:
108 description: GPIO controlled connection to PERST# signal
665 perst-gpios = <&tlmm 70 GPIO_ACTIVE_LOW>;
|
| D | qcom,pcie-sm8350.yaml | 159 perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
|
| D | qcom,pcie-sm8150.yaml | 155 perst-gpios = <&tlmm 35 GPIO_ACTIVE_HIGH>;
|
| D | qcom,pcie-sa8775p.yaml | 163 perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
|
| D | ti-pci.txt | 61 - gpios : Should be added if a GPIO line is required to drive PERST# line
|
| D | qcom,pcie-sc7280.yaml | 176 perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
|
| D | qcom,pcie-sm8250.yaml | 170 perst-gpios = <&tlmm 79 GPIO_ACTIVE_LOW>;
|
| D | qcom,pcie-sm8550.yaml | 168 perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
|
| D | qcom,pcie-x1e80100.yaml | 161 perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
|
| D | qcom,pcie-sc8280xp.yaml | 173 perst-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>;
|
| D | qcom,pcie-sm8450.yaml | 181 perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
|
| D | brcm,stb-pcie.yaml | 134 - const: perst
|
| D | mvebu-pci.txt | 81 - reset-gpios: optional GPIO to PERST#
151 /* low-active PERST# reset on GPIO 25 */
|
| D | nvidia,tegra194-pcie-ep.yaml | 77 that is being used as PERST input signal. Please refer to pci.txt.
|
| /Documentation/devicetree/bindings/pinctrl/ |
| D | mediatek,mt76x8-pinctrl.yaml | 40 p4led_an, p4led_kn, pcie, pcm, perst, pwm, pwm0, pwm1,
82 p4led_kn, perst, pwm0, pwm1, refclk, sdmode, spi,
226 const: perst
230 enum: [perst]
|
| D | qcom,sm8150-pinctrl.yaml | 138 perst-pins {
|
| /Documentation/ABI/testing/ |
| D | sysfs-class-cxl | 220 "none" means PERST will not cause image to be loaded to the
225 "user" and "factory" means PERST will cause either the user or
227 Default is to reload on PERST whichever image the card has
235 Writing 1 will issue a PERST to card provided there are no
238 Writing -1 will do a force PERST irrespective of any active
247 Trust that when an image is reloaded via PERST, it will not
|
| /Documentation/devicetree/bindings/reset/ |
| D | brcm,bcm4908-misc-pcie-reset.yaml | 9 description: This document describes reset controller handling PCIe PERST#
|
| /Documentation/devicetree/bindings/phy/ |
| D | fsl,imx8-pcie-phy.yaml | 41 - const: perst
|