Searched full:push (Results 1 – 25 of 106) sorted by relevance
12345
| /Documentation/devicetree/bindings/watchdog/ |
| D | aspeed,ast2400-wdt.yaml | 73 aspeed,ext-push-pull:
77 signal pin's drive type to push-pull. If aspeed,ext-push-pull is not
83 If both aspeed,external-signal and aspeed,ext-push-pull are specified in
106 - aspeed,ext-push-pull
122 - aspeed,ext-push-pull
|
| /Documentation/netlink/specs/ |
| D | ovs_flow.yaml | 257 name: ovs-action-push-vlan
264 doc: Tag protocol identifier (TPID) to push.
269 doc: Tag control identifier (TCI) to push.
303 name: ovs-action-push-mpls
311 MPLS label stack entry to push
329 MPLS label stack entry to push
620 name: push-vlan
622 struct: ovs-action-push-vlan
623 doc: Push a new outermost 802.1Q or 802.1ad header onto the packet.
643 name: push-mpls
[all …]
|
| D | ethtool.yaml | 212 name: tx-push
215 name: rx-push
218 name: tx-push-buf-len
221 name: tx-push-buf-len-max
1397 - tx-push
1398 - rx-push
1399 - tx-push-buf-len
1400 - tx-push-buf-len-max
|
| /Documentation/devicetree/bindings/net/ |
| D | smsc,lan9115.yaml | 55 smsc,irq-push-pull:
57 description: Indicates the IRQ type is push-pull
109 smsc,irq-push-pull;
|
| D | ti,k3-am654-cpts.yaml | 20 - hardware timestamp push inputs (HWx_TS_PUSH)
25 - external hardware timestamp push inputs (HWx_TS_PUSH) timestamping
88 Number of hardware timestamp push inputs (HWx_TS_PUSH)
|
| /Documentation/bpf/ |
| D | map_queue_stack.rst | 14 push operations that are exposed to BPF programs through the respective
20 - ``BPF_MAP_UPDATE_ELEM`` -> push
77 A userspace program can push ``value`` onto a queue or stack using libbpf's
|
| D | map_bloom_filter.rst | 20 - push: adding an element to the map
28 - ``BPF_MAP_UPDATE_ELEM`` -> push
|
| /Documentation/devicetree/bindings/mfd/ |
| D | st,stmfx.yaml | 72 drive-push-pull: true
116 drive-push-pull;
|
| /Documentation/devicetree/bindings/i2c/ |
| D | i2c-mt65xx.yaml | 95 mediatek,use-push-pull:
96 description: Use push-pull mode I/O config
|
| D | allwinner,sun6i-a31-p2wi.yaml | 7 title: Allwinner A31 P2WI (Push/Pull 2 Wires Interface)
|
| /Documentation/devicetree/bindings/net/can/ |
| D | nxp,sja1000.yaml | 68 <0x06> : TX0 push-pull
72 <0x30> : TX1 push-pull
|
| /Documentation/arch/arm/keystone/ |
| D | knav-qmss.rst | 21 queue pool management (allocation, push, pop and notify) and descriptor
25 allocate descriptor pools, map the descriptors, push/pop to queues etc. For
|
| /Documentation/devicetree/bindings/input/ |
| D | max77650-onkey.yaml | 32 The system's button is a slide switch, not the default push button.
|
| /Documentation/devicetree/bindings/sound/ |
| D | cirrus,cs35l45.yaml | 113 4 = Pin acts as push-pull output INT. Active low.
114 5 = Pin acts as push-pull output INT. Active high.
|
| D | cirrus,cs35l41.yaml | 148 4 = Push-pull INTB (active low)
149 5 = Push-pull INT (active high)
|
| /Documentation/arch/powerpc/ |
| D | qe_firmware.rst | 128 | | push command | given by the application, the software must |
129 | | | assert a special host command (push command)|
135 | | push command | command (push command) and immediately |
150 | 3 | General push | Indicates that the s/w has to initialize |
156 | 4 | General push | Indicates that after issuing Ethernet TX |
|
| /Documentation/accounting/ |
| D | cgroupstats.rst | 15 The current model for cgroupstats is a pull, a push model (to post
|
| /Documentation/translations/zh_CN/admin-guide/ |
| D | bug-hunting.rst | 219 push %ebp
220 push %edi
221 push %esi
222 push %ebx
|
| /Documentation/translations/zh_TW/admin-guide/ |
| D | bug-hunting.rst | 222 push %ebp
223 push %edi
224 push %esi
225 push %ebx
|
| /Documentation/maintainer/ |
| D | pull-requests.rst | 124 Now that you have a local signed tag, you need to push it up to where it
127 git push origin char-misc-4.15-rc1
153 a handy way to remember to actually push it to a public location.
|
| /Documentation/networking/device_drivers/ethernet/amazon/ |
| D | ena.rst | 138 - **Low Latency Queue (LLQ) mode or "push-mode":**
280 - Populates ``ena_buf`` for the push buffer (if the driver and device are
281 in push mode).
291 * This function also copies the ENA descriptors and the push buffer
292 to the Device memory space (if in push mode).
|
| /Documentation/devicetree/bindings/iio/imu/ |
| D | bosch,bmi323.yaml | 43 open drain. If not set, defaults to push-pull.
|
| D | bosch,bmi160.yaml | 42 open drain. If not set, defaults to push-pull.
|
| /Documentation/devicetree/bindings/soc/ti/ |
| D | keystone-navigator-qmss.txt | 15 queue pool management (allocation, push, pop and notify) and descriptor
41 - Queue Management/Queue Proxy region for queue Push.
47 - Queue Management/Queue Proxy region for queue Push/Pop.
|
| /Documentation/process/ |
| D | 7.AdvancedTopics.rst | 90 So, once you push a set of changes to your publicly-available server, those
92 you try to push changes which do not result in a fast-forward merge
147 sure that you have remembered to push those changes to the public server.
|
12345