Searched full:sdb (Results 1 – 18 of 18) sorted by relevance
| /Documentation/target/ |
| D | tcm_mod_builder.rst | 32 …target:/mnt/sdb/lio-core-2.6.git/Documentation/target# python tcm_mod_builder.py -p iSCSI -m tcm_n… 33 tcm_dir: /mnt/sdb/lio-core-2.6.git/Documentation/target/../../ 36 /mnt/sdb/lio-core-2.6.git/Documentation/target/../../drivers/target/tcm_nab5000 39 /mnt/sdb/lio-core-2.6.git/Documentation/target/../../drivers/target/tcm_nab5000 41 /mnt/sdb/lio-core-2.6.git/Documentation/target/../../drivers/target/tcm_nab5000/tcm_nab5000_base.h 43 /mnt/sdb/lio-core-2.6.git/Documentation/target/../../include/target/target_core_fabric_ops.h 45 …/mnt/sdb/lio-core-2.6.git/Documentation/target/../../drivers/target/tcm_nab5000/tcm_nab5000_fabric… 47 …/mnt/sdb/lio-core-2.6.git/Documentation/target/../../drivers/target/tcm_nab5000/tcm_nab5000_fabric… 49 …/mnt/sdb/lio-core-2.6.git/Documentation/target/../../drivers/target/tcm_nab5000/tcm_nab5000_config… 51 /mnt/sdb/lio-core-2.6.git/Documentation/target/../../drivers/target/tcm_nab5000/Kbuild [all …]
|
| /Documentation/admin-guide/device-mapper/ |
| D | log-writes.rst | 107 TABLE="0 $(blockdev --getsz /dev/sdb) log-writes /dev/sdb /dev/sdc" 119 replay-log --log /dev/sdc --replay /dev/sdb --end-mark fsync 120 mount /dev/sdb /mnt/btrfs-test 127 TABLE="0 $(blockdev --getsz /dev/sdb) log-writes /dev/sdb /dev/sdc" 138 replay-log --log /dev/sdc --replay /dev/sdb --end-mark mkfs 139 btrfsck /dev/sdb 140 replay-log --log /dev/sdc --replay /dev/sdb --start-mark mkfs \ 141 --fsck "btrfsck /dev/sdb" --check fua
|
| D | dm-service-time.rst | 78 In case that 2 paths (sda and sdb) are used with repeat_count == 128 79 and sda has an average throughput 1GB/s and sdb has 4GB/s, 80 'relative_throughput' value may be '1' for sda and '4' for sdb:: 92 Or '2' for sda and '8' for sdb would be also true::
|
| D | dm-queue-length.rst | 37 In case that 2 paths (sda and sdb) are used with repeat_count == 128.
|
| D | cache-policies.rst | 128 dmsetup create blah --table "0 268435456 cache /dev/sdb /dev/sdc \
|
| /Documentation/devicetree/bindings/sound/ |
| D | realtek,rt1015p.yaml | 22 sdb-gpios: 42 sdb-gpios = <&pio 175 GPIO_ACTIVE_HIGH>;
|
| D | fsl-asoc-card.yaml | 56 - fsl,imx6sx-sdb-mqs 57 - fsl,imx6sx-sdb-wm8962 71 - fsl,imx6sx-sdb-spdif
|
| /Documentation/devicetree/bindings/arm/ |
| D | arm,integrator.yaml | 37 - description: ARM Integrator Standard Development Board (SDB) Platform, 38 this board is a PCI-based board conforming to the Microsoft SDB
|
| D | fsl.yaml | 628 - fsl,imx6sx-sdb # i.MX6 SoloX SDB Board 629 - fsl,imx6sx-sdb-reva # i.MX6 SoloX SDB Rev-A Board 871 - fsl,imx7d-sdb # i.MX7 SabreSD Board 872 - fsl,imx7d-sdb-reva # i.MX7 SabreSD Rev-A Board
|
| /Documentation/admin-guide/ |
| D | bcache.rst | 50 bcache make -B /dev/sdb 57 bcache make -B /dev/sda /dev/sdb -C /dev/sdc 66 echo /dev/sdb > /sys/fs/bcache/register 116 echo 1 > /sys/block/sdb/bcache/running 118 (You need to use /sys/block/sdb (or whatever your backing device is called), not 120 partition, the bcache directory would be at /sys/block/sdb/sdb2/bcache) 166 host:/sys/block/sdb/sdb1/bcache# echo 1 > running
|
| D | devices.txt | 202 16 = /dev/sdb Second SCSI disk whole disk
|
| D | cgroup-v2.rst | 1915 shows that on sdb, the controller is enabled, will consider
|
| /Documentation/arch/powerpc/ |
| D | cxlflash.rst | 85 scsi block devices (/dev/sdb, /dev/sdc etc.) for each unique LUN 97 block device (/dev/sdb) may be carved up into any number of distinct 103 block device (/dev/sdb) may be opened directly by the block library 140 with the scsi disk device (/dev/sdb) that was created during LUN
|
| /Documentation/devicetree/bindings/pinctrl/ |
| D | nvidia,tegra20-pinmux.yaml | 42 lsda, lsdi, lspi, lvp0, lvp1, lvs, owc, pmc, pta, rm, sdb,
|
| /Documentation/devicetree/bindings/leds/ |
| D | issi,is31fl319x.yaml | 42 description: GPIO attached to the SDB pin.
|
| /Documentation/admin-guide/cgroup-v1/ |
| D | blkio-controller.rst | 116 Configure weight=300 on /dev/sdb (8:16) in this cgroup::
|
| /Documentation/power/ |
| D | basic-pm-debugging.rst | 222 http://en.opensuse.org/SDB:Suspend_to_RAM (S2RAM_LINK).
|
| /Documentation/arch/m68k/ |
| D | kernel-options.rst | 80 /dev/sdb: -> 0x0810 (second SCSI disk)
|