Searched full:save (Results 1 – 25 of 215) sorted by relevance
123456789
| /Documentation/tools/rtla/ |
| D | common_osnoise_options.rst | 17 If **-T** is set, it will also save the trace to the output.
22 If **-T** is set, it will also save the trace to the output.
31 Save the stopped trace to [*file|osnoise_trace.txt*].
|
| D | common_timerlat_options.rst | 22 Save the stack trace at the *IRQ* if a *Thread* latency is higher than the
27 Save the stopped trace to [*file|timerlat_trace.txt*].
|
| /Documentation/sound/designs/ |
| D | powersave.rst | 12 done fully or partially. It'll save a certain power consumption, thus
27 automatic power-save mode with 10 seconds, write to
40 power_save_controller. This enables/disables the power-save mode of
|
| /Documentation/devicetree/bindings/net/bluetooth/ |
| D | nxp,88w8987-bt.yaml | 13 are used during FW download. To enable power save mode, the host
14 asserts break signal over UART-TX line to put the chip into power save
|
| /Documentation/ABI/testing/ |
| D | sysfs-driver-w1_therm | 21 (WO) writing that file will either trigger a save of the
26 * 'save': save device RAM to EEPROM
54 power is lost. Trigger a 'save' to EEPROM command to keep
99 * '0' : save the 2 or 3 bytes to the device EEPROM
|
| D | sysfs-kernel-fadump | 33 save the crash dump.
40 FADump to save the crash dump in bytes.
|
| D | sysfs-class-firmware-attributes | 297 echo "save signature" > authentication/Admin/save_signature
395 to allow a user to bulk set the attributes, and then trigger a final save. This allows
398 Read the attribute to check what save mode is enabled (single or bulk).
403 Write the attribute with 'bulk' to enable bulk save mode.
409 When in bulk mode write 'save' to trigger a save of all currently modified attributes.
410 Note, once a save has been triggered, in bulk mode, attributes can no longer be set and
411 will return a permissions error. This is to prevent users hitting the 48+ save limitation
414 # echo save > /sys/class/firmware-attributes/thinklmi/attributes/save_settings
|
| D | sysfs-bus-iio-ina2xx-adc | 12 save the additional i2c transaction, which will improve the bandwidth
|
| /Documentation/arch/arm/nwfpe/ |
| D | notes.rst | 11 often uses an stfe instruction to save f4 on the stack upon entry to a
32 in extended precision, due to the stfe instruction used to save f4 in log(y).
|
| /Documentation/sound/soc/ |
| D | clocking.rst | 18 their speed can be altered by software (depending on the system use and to save
40 rate, number of channels and word size) to save on power.
|
| /Documentation/ABI/obsolete/ |
| D | sysfs-kernel-fadump_release_mem | 10 save the crash dump.
|
| /Documentation/devicetree/bindings/net/ |
| D | mscc-phy-vsc8531.txt | 34 - load-save-gpios : GPIO used for the load/save operation of the PTP
72 load-save-gpios = <&gpio 10 GPIO_ACTIVE_HIGH>;
|
| /Documentation/core-api/ |
| D | gfp_mask-from-fs-io.rst | 43 FS/IO code then simply calls the appropriate save function before
50 Please note that the proper pairing of save/restore functions
|
| /Documentation/virt/kvm/s390/ |
| D | s390-pv.rst | 72 Secure Interception General Register Save Area. Guest GRs and most of
76 Register Save Area.
79 save area and the real register numbers will be hidden.
|
| /Documentation/trace/ |
| D | ftrace-design.rst | 88 /* save any bare state needed in order to do initial checking */
100 /* save all state needed by the ABI (see paragraph above) */
121 some functions to save (hijack) and restore the return address.
165 /* save all state needed by the ABI */
192 /* save all state needed by the ABI (see paragraph above) */
318 /* save all state needed by the ABI (see paragraph above) */
|
| /Documentation/arch/arm64/ |
| D | sve.rst | 535 (*) callee-save:
537 FPCR contains callee-save and caller-save bits. See [4] for details.
546 * All SVE register bits that are not shared with FP/SIMD are caller-save.
548 * Z8 bits [63:0] .. Z15 bits [63:0] are callee-save.
551 save in the base procedure call standard.
589 (*) callee-save:
591 FPCR contains a mixture of callee-save and caller-save bits.
|
| /Documentation/devicetree/bindings/power/ |
| D | brcm,bcm63xx-power.yaml | 14 to enable/disable certain components in order to save power.
|
| D | starfive,jh7110-pmu.yaml | 14 powered on/off by software based on different application scenes to save power.
|
| /Documentation/devicetree/bindings/display/ |
| D | ste,mcde.yaml | 74 description: phandles to the high speed and low power (energy save) clocks
160 /* This DSI port only has the Low Power / Energy Save clock */
|
| /Documentation/devicetree/bindings/soc/qcom/ |
| D | qcom,dcc.yaml | 13 DCC (Data Capture and Compare) is a DMA engine which is used to save
|
| /Documentation/cpu-freq/ |
| D | index.rst | 10 fly. This is a nice method to save battery power, because the lower
|
| /Documentation/virt/kvm/ |
| D | review-checklist.rst | 16 4. New state must include support for save/restore.
|
| /Documentation/power/ |
| D | pm_qos_interface.rst | 35 Clients of PM QoS need to save the returned handle for future use in other
110 Clients of dev_pm_qos need to save the handle for future use in other
186 mode chosen by the hardware attempts to save energy in an overly aggressive way,
|
| /Documentation/hwmon/ |
| D | sfctemp.rst | 31 but may be disabled to save power.
|
| /Documentation/arch/arm/sunxi/ |
| D | clocks.rst | 11 A: The 24MHz oscillator allows gating to save power. Indeed, if gated
|
123456789