Searched full:vbus (Results 1 – 25 of 98) sorted by relevance
1234
| /Documentation/devicetree/bindings/regulator/ |
| D | qcom,usb-vbus-regulator.yaml | 4 $id: http://devicetree.org/schemas/regulator/qcom,usb-vbus-regulator.yaml#
7 title: The Qualcomm PMIC VBUS output regulator driver
13 This regulator driver controls the VBUS output by the Qualcomm PMIC. This
24 - qcom,pm8150b-vbus-reg
27 - qcom,pm4125-vbus-reg
28 - qcom,pm6150-vbus-reg
29 - qcom,pm7250b-vbus-reg
30 - qcom,pmi632-vbus-reg
31 - const: qcom,pm8150b-vbus-reg
35 description: VBUS output base address
[all …]
|
| D | siliconmitus,sm5703-regulator.yaml | 15 Regulator nodes should be named as USBLDO_<number>, BUCK, VBUS, LDO_<number>.
27 vbus:
32 Properties for the VBUS regulator.
|
| /Documentation/devicetree/bindings/usb/ |
| D | usb-nop-xceiv.yaml | 36 vbus-detect-gpio:
37 description: Should specify the GPIO detecting a VBus insertion
40 vbus-supply:
41 description: regulator supplying VBUS. It will be enabled and disabled
68 vbus-detect-gpio = <&gpio2 13 GPIO_ACTIVE_HIGH>;
69 vbus-supply = <&vbus_regulator>;
|
| D | ohci-da8xx.txt | 12 - vbus-supply: phandle of regulator that controls vbus power / over-current
22 vbus-supply = <®_usb_ohci>;
|
| D | fcs,fusb302.yaml | 22 vbus-supply:
23 description: VBUS power supply
34 - vbus-supply
53 vbus-supply = <&vbus_typec>;
|
| D | maxim,max3421.txt | 7 - maxim,vbus-en-pin: <GPOUTx ACTIVE_LEVEL>
8 GPOUTx is the number (1-8) of the GPOUT pin of MAX3421E to drive Vbus.
19 maxim,vbus-en-pin = <3 1>;
|
| D | qcom,pmic-typec.yaml | 45 - description: Type-C CC attach notification, VBUS error, tCCDebounce done
49 - description: Type-C VBUS state change
69 - const: vbus-change
82 vdd-vbus-supply:
83 description: VBUS power supply.
98 - vdd-vbus-supply
164 "vbus-change",
177 vdd-vbus-supply = <&pm8150b_vbus>;
|
| D | atmel-usb.txt | 16 - atmel,vbus-gpio: If present, specifies a gpio that needs to be
70 - atmel,vbus-gpio: If present, specifies a gpio that needs to be
79 atmel,vbus-gpio = <&pioC 5 0>;
104 - atmel,vbus-gpio: If present, specifies a gpio that allows to detect whether
105 vbus is present (USB is connected).
124 atmel,vbus-gpio = <&pioB 19 0>;
|
| D | maxim,max3420-udc.yaml | 31 - description: vbus detection irq
37 - const: vbus
64 interrupt-names = "udc", "vbus";
|
| /Documentation/devicetree/bindings/reset/ |
| D | renesas,rzg2l-usbphy-ctrl.yaml | 45 regulator-vbus:
47 description: USB VBUS regulator
58 - regulator-vbus
74 regulator-vbus {
75 regulator-name = "vbus";
|
| /Documentation/devicetree/bindings/phy/ |
| D | nvidia,tegra194-xusb-padctl.yaml | 40 for the USB signal, the VBUS power supply, the USB 2.0 companion port for
72 description: USB I/Os, VBUS, ID, REXT, D+/D- power supply. Must
254 vbus-supply:
255 description: A phandle to the regulator supplying the VBUS
292 vbus-supply:
293 description: A phandle to the regulator supplying the VBUS
330 vbus-supply:
331 description: A phandle to the regulator supplying the VBUS
368 vbus-supply:
369 description: A phandle to the regulator supplying the VBUS
[all …]
|
| D | nvidia,tegra210-xusb-padctl.yaml | 40 for the USB signal, the VBUS power supply, the USB 2.0 companion port for
382 vbus-supply:
383 description: A phandle to the regulator supplying the VBUS
420 vbus-supply:
421 description: A phandle to the regulator supplying the VBUS
458 vbus-supply:
459 description: A phandle to the regulator supplying the VBUS
496 vbus-supply:
497 description: A phandle to the regulator supplying the VBUS
507 vbus-supply:
[all …]
|
| D | nvidia,tegra186-xusb-padctl.yaml | 40 for the USB signal, the VBUS power supply, the USB 2.0 companion port for
74 description: USB I/Os, VBUS, ID, REXT, D+/D- power supply. Must
263 vbus-supply:
264 description: A phandle to the regulator supplying the VBUS
301 vbus-supply:
302 description: A phandle to the regulator supplying the VBUS
339 vbus-supply:
340 description: A phandle to the regulator supplying the VBUS
367 vbus-supply:
368 description: A phandle to the regulator supplying the VBUS
[all …]
|
| D | brcm,ns2-drd-phy.txt | 13 - vbus-gpios: vbus gpio binding
29 vbus-gpios = <&gpio_g 31 0>;
|
| D | nvidia,tegra124-xusb-padctl.yaml | 40 for the USB signal, the VBUS power supply, the USB 2.0 companion port for
360 vbus-supply:
361 description: A phandle to the regulator supplying the VBUS
395 vbus-supply:
396 description: A phandle to the regulator supplying the VBUS
430 vbus-supply:
431 description: A phandle to the regulator supplying the VBUS
444 vbus-supply:
445 description: A phandle to the regulator supplying the VBUS
452 vbus-supply:
[all …]
|
| D | allwinner,suniv-f1c100s-usb-phy.yaml | 47 description: GPIO to the USB OTG VBUS detect pin
50 description: Power supply to detect the USB OTG VBUS
53 description: Regulator controlling USB OTG VBUS
|
| /Documentation/ABI/testing/ |
| D | sysfs-platform-twl4030-usb | 1 What: /sys/bus/platform/devices/*twl4030-usb/vbus
3 Read-only status reporting if VBUS (approx 5V)
|
| D | sysfs-platform-tahvo-usb | 10 What: /sys/bus/platform/devices/tahvo-usb/vbus
14 Read the current VBUS state.
|
| /Documentation/devicetree/bindings/power/supply/ |
| D | mt6360_charger.yaml | 25 usb-otg-vbus-regulator:
42 otg_vbus_regulator: usb-otg-vbus-regulator {
43 regulator-name = "usb-otg-vbus";
|
| D | cpcap-charger.yaml | 35 - description: VBUS valid interrupt
54 - description: VBUS voltage
62 - const: vbus
103 "vbus", "chg_isense",
|
| D | mediatek,mt6370-charger.yaml | 46 Use ADC channel to read VBUS, IBUS, IBAT, etc., info.
50 VBUS voltage with lower accuracy (+-75mV) but higher measure
53 VBUS voltage with higher accuracy (+-30mV) but lower measure
78 usb-otg-vbus-regulator:
|
| D | richtek,rt9471.yaml | 37 usb-otg-vbus-regulator:
65 usb-otg-vbus-regulator {
66 regulator-name = "usb-otg-vbus";
|
| /Documentation/devicetree/bindings/rtc/ |
| D | ti,k3-rtc.yaml | 31 - description: VBUS Interface clock
36 - const: vbus
60 clock-names = "vbus", "osc32k";
|
| /Documentation/firmware-guide/acpi/ |
| D | extcon-intel-int3496.rst | 10 USB-otg port, as well as how it optionally can enable Vbus output on the
19 Index 1 The output gpio for enabling Vbus output from the device to the otg
20 port, write 1 to enable the Vbus output (this gpio descriptor may
31 vbus index 1
|
| /Documentation/devicetree/bindings/extcon/ |
| D | extcon-ptn5150.yaml | 34 vbus-gpios:
37 GPIO pin (output) used to control VBUS. If skipped, no such control
65 vbus-gpios = <&msmgpio 148 GPIO_ACTIVE_HIGH>;
|
1234