Searched full:acknowledge (Results 1 – 25 of 39) sorted by relevance
12
| /Documentation/ABI/stable/ |
| D | sysfs-firmware-opal-elog | 24 entries, read them out and acknowledge them.
27 entries than firmware can, so after you acknowledge
55 acknowledge: Writing 'ack' to this file will acknowledge
61 operations (currently just acknowledge).
|
| D | sysfs-firmware-opal-dump | 39 acknowledge: When 'ack' is written to this, we will
40 acknowledge that we've retrieved the
|
| /Documentation/images/ |
| D | COPYING-logo | 4 and is freely usable as long as you acknowledge Larry as the original
16 as long as you acknowledge Larry, Garrett and IFo as above.
|
| /Documentation/devicetree/bindings/remoteproc/ |
| D | qcom,pas-common.yaml | 34 - description: Stop acknowledge interrupt
35 - description: Shutdown acknowledge interrupt
|
| D | qcom,sc7280-adsp-pil.yaml | 36 - description: Stop acknowledge interrupt
37 - description: Shutdown acknowledge interrupt
|
| D | qcom,sc7280-wpss-pil.yaml | 32 - description: Stop acknowledge interrupt
33 - description: Shutdown acknowledge interrupt
|
| D | qcom,sc7180-mss-pil.yaml | 42 - description: Stop acknowledge interrupt
43 - description: Shutdown acknowledge interrupt
|
| D | qcom,sc7280-mss-pil.yaml | 46 - description: Stop acknowledge interrupt
47 - description: Shutdown acknowledge interrupt
|
| D | qcom,msm8996-mss-pil.yaml | 46 - description: Stop acknowledge interrupt
47 - description: Shutdown acknowledge interrupt
|
| D | qcom,qcs404-cdsp-pil.yaml | 32 - description: Stop acknowledge interrupt
|
| D | qcom,sdm845-adsp-pil.yaml | 32 - description: Stop acknowledge interrupt
|
| D | qcom,msm8916-mss-pil.yaml | 45 - description: Stop acknowledge interrupt
|
| /Documentation/devicetree/bindings/mailbox/ |
| D | hisilicon,hi6220-mailbox.txt | 27 mailbox driver uses it to acknowledge interrupt
36 flag" mode or IRQ generated mode to acknowledge a TX
|
| /Documentation/driver-api/ |
| D | connector.rst | 73 acknowledge number. The sequence number may be copied into
80 acknowledge number MUST be the same + 1.
85 acknowledge is not equal to the sequence number in the original
|
| /Documentation/devicetree/bindings/dma/stm32/ |
| D | st,stm32-mdma.yaml | 47 4. A 32bit value specifying the register to be used to acknowledge the request
49 5. A 32bit mask specifying the value to be written to acknowledge the request
|
| D | st,stm32-dma.yaml | 43 -bit 4: alternative DMA request/acknowledge protocol
|
| /Documentation/arch/arm/ |
| D | interrupts.rst | 57 * Acknowledge the IRQ.
154 acknowledge the SA1110 IRQ each time you re-read the SA1111 IRQ status.
157 (eg, SMC9196), the handler must mask or acknowledge the parent IRQ
|
| /Documentation/i2c/ |
| D | i2c-protocol.rst | 15 A, NA (1 bit) Acknowledge (ACK) and Not Acknowledge (NACK) bit
|
| D | smbus-protocol.rst | 43 A, NA (1 bit) Acknowledge (ACK) and Not Acknowledge (NACK) bit
|
| /Documentation/w1/ |
| D | w1-netlink.rst | 187 Each message also includes sequence and acknowledge numbers.
192 acknowledge number is set to seq+1.
|
| /Documentation/devicetree/bindings/i2c/ |
| D | renesas,rmobile-iic.yaml | 108 - description: Non-acknowledge Detection Interrupt (TACKI)
|
| /Documentation/usb/ |
| D | CREDITS | 98 way to acknowledge the importance of Linux and to allow
|
| /Documentation/networking/device_drivers/cellular/qualcomm/ |
| D | rmnet.rst | 174 1 is to acknowledge the receipt of a command
|
| /Documentation/driver-api/surface_aggregator/ |
| D | ssh.rst | 121 - Sent to acknowledge receival of |DATA| frame.
143 |DATA_SEQ|-type frame, the receiving party has to acknowledge receival of
|
| /Documentation/arch/arm/stm32/ |
| D | stm32-dma-mdma-chaining.rst | 200 4. The 32bit value specifying the register to be used to acknowledge the
205 5. The 32bit mask specifying the value to be written to acknowledge the
|
12