Searched full:adjust (Results 1 – 25 of 147) sorted by relevance
123456
| /Documentation/devicetree/bindings/phy/ |
| D | fsl,imx8mq-usb-phy.yaml | 53 Adjust amount of current sourced to DPn and DMn after a J-to-K
60 Adjust the boosted transmit launch pk-pk differential amplitude
65 Adjust the voltage level used to detect a disconnect event at the host
72 Adjust TX de-emphasis attenuation in dB at nominal
|
| /Documentation/driver-api/media/drivers/ |
| D | radiotrack.rst | 130 radio enable, tuner adjust disable)
133 radio disable, tuner adjust disable)
139 radio enable, tuner adjust disable)
144 radio enable, tuner adjust disable)
149 radio enable, tuner adjust disable)
161 disable, "zero" bit phase 1, tuner adjust)
163 disable, "zero" bit phase 2, tuner adjust)
166 disable, "one" bit phase 1, tuner adjust)
168 disable, "one" bit phase 2, tuner adjust)
|
| /Documentation/userspace-api/media/v4l/ |
| D | vidioc-g-selection.rst | 67 must be filled with zeros. The driver may adjust coordinates of the
72 - ``0`` - The driver can adjust the rectangle size freely and shall
85 Please refer to :ref:`sel-const-adjust`.
96 2. Adjust width, height, left, and top to hardware limits and
118 .. _sel-const-adjust:
181 It is not possible to adjust struct :c:type:`v4l2_rect`
|
| D | selection-api-configuration.rst | 17 Therefore, as usual, drivers are expected to adjust the requested
40 The driver may further adjust the requested size and/or position
59 bounds rectangle. The driver must adjust the composing rectangle to fit
100 further adjust the requested size and/or position according to hardware
111 driver must adjust the area to fit to the bounding limits. Moreover, the
|
| D | crop.rst | 92 capture boundaries and the driver may further adjust the requested size
120 usual, drivers are expected to adjust the requested parameters and
125 signal. If the driver has to adjust both to satisfy hardware
127 driver should preferably adjust the opposite one. The
129 the driver state and therefore only adjust the requested rectangle.
|
| /Documentation/devicetree/bindings/serial/ |
| D | nvidia,tegra20-hsuart.yaml | 58 nvidia,adjust-baud-rates:
78 we use nvidia,adjust-baud-rates.
86 nvidia,adjust-baud-rates = <0 9600 100>,
124 nvidia,adjust-baud-rates = <1000000 4000000 136>; /* 1.36% shift */
|
| /Documentation/devicetree/ |
| D | dynamic-resolution-notes.rst | 20 2. Adjust all the local phandles of the tree to resolve by that amount.
21 3. Using the __local__fixups__ node information adjust all local references
|
| /Documentation/devicetree/bindings/mfd/ |
| D | allwinner,sun4i-a10-ts.yaml | 33 allwinner,tp-sensitive-adjust:
72 allwinner,tp-sensitive-adjust = <0>;
|
| /Documentation/ABI/testing/ |
| D | sysfs-driver-hid-picolcd | 31 Description: Make it possible to adjust defio refresh rate.
40 it only makes sense to adjust this value if only one or two
|
| D | sysfs-bus-iio-filter-admv8818 | 8 - auto -> Adjust bandpass filter to track changes in input clock rate.
|
| D | sysfs-bus-iio-frequency-adf4350 | 18 adjust the reference frequency accordingly.
|
| /Documentation/netlink/specs/ |
| D | dpll.yaml | 327 name: phase-adjust-min
330 name: phase-adjust-max
333 name: phase-adjust
529 - phase-adjust-min
530 - phase-adjust-max
531 - phase-adjust
561 - phase-adjust
|
| /Documentation/devicetree/bindings/iio/light/ |
| D | sharp,gp2ap002.yaml | 47 device-unique and adjust the optical setting for proximity detection
54 device-unique and adjust the optical setting for proximity detection
|
| /Documentation/devicetree/bindings/usb/ |
| D | chipidea,usb2-imx.yaml | 110 samsung,picophy-dc-vol-level-adjust:
112 HS DC Voltage Level Adjustment. Adjust the high-speed transmitter DC
119 fsl,picophy-rise-fall-time-adjust:
121 HS Transmitter Rise/Fall Time Adjustment. Adjust the rise/fall times
|
| /Documentation/devicetree/bindings/regulator/ |
| D | rohm,bd71847-regulator.yaml | 138 Feedback-pin has pull-up connection to adjust voltage range. This is
143 Feedback-pin has pull-up connection to adjust voltage range. This is
148 Feedback-pin has pull-up connection to adjust voltage range. This is
|
| D | rohm,bd71837-regulator.yaml | 143 Feedback-pin has pull-up connection to adjust voltage range. This is
148 Feedback-pin has pull-up connection to adjust voltage range. This is
153 Feedback-pin has pull-up connection to adjust voltage range. This is
|
| D | vctrl.txt | 23 undesiredly since the output voltage does not adjust
|
| /Documentation/devicetree/bindings/power/ |
| D | ti-smartreflex.txt | 3 SmartReflex is used to set and adjust the SoC operating points.
|
| /Documentation/admin-guide/acpi/ |
| D | fan_performance_states.rst | 69 _FSL object. User can adjust fan speed using thermal sysfs cooling device.
73 is supported then user can also adjust to some other speeds which are
|
| /Documentation/devicetree/bindings/clock/ |
| D | mediatek,mt8186-fhctl.yaml | 14 some PLLs to adopt "hopping" mechanism to adjust their frequency.
|
| /Documentation/userspace-api/media/rc/ |
| D | lirc-get-rec-resolution.rst | 39 used by userspace applications like lircd to automatically adjust the
|
| /Documentation/filesystems/ |
| D | ocfs2-online-filecheck.rst | 84 default size is 10, and can be adjust between the range of 10 ~ 100. You can
85 adjust the size like this::
|
| /Documentation/devicetree/bindings/pinctrl/ |
| D | fsl,mxs-pinctrl.txt | 28 one is to adjust the pin configuration for some particular pins that need a
39 there to adjust configurations for some pins in the group.
|
| /Documentation/devicetree/bindings/net/ |
| D | marvell-neta-bm.txt | 15 Otherwise the driver would adjust a given number or choose default if
|
| /Documentation/sound/designs/ |
| D | powersave.rst | 26 adjust the value via sysfs on the fly. For example, to turn on the
|
123456