Searched full:assuming (Results 1 – 25 of 135) sorted by relevance
123456
| /Documentation/networking/ |
| D | multiqueue.rst | 51 qdiscs. To add the MULTIQ qdisc to your network device, assuming the device
57 the device reports, and bring the qdisc online. Assuming eth0 has 4 Tx
69 skbedit, has been added. Assuming you wanted to route all traffic to a
|
| /Documentation/devicetree/bindings/rtc/ |
| D | ingenic,rtc.yaml | 68 (assuming RTC clock at 32 kHz)
76 (assuming RTC clock at 32 kHz)
|
| /Documentation/hwmon/ |
| D | ltc2990.rst | 55 curr1_input Current in mA across V1-V2 assuming a 1mOhm sense resistor
56 curr2_input Current in mA across V3-V4 assuming a 1mOhm sense resistor
|
| D | g760a.rst | 30 from the measured speed pulse period by assuming again a 32kHz clock
|
| D | sl28cpld.rst | 35 fan1_input Fan RPM. Assuming 2 pulses per revolution.
|
| D | adm1025.rst | 54 process, assuming that the BIOS set it up properly beforehand. If it turns
|
| /Documentation/admin-guide/ |
| D | sysfs-rules.rst | 128 Assuming ``/sys/class/<subsystem>`` and ``/sys/bus/<subsystem>``, or
135 at the same level, never in a hierarchy. Assuming the block subsystem to
146 path as an element. Assuming the existence of the "device"-link for
156 element. Assuming the existence of these links for devices which are
|
| D | binderfs.rst | 79 Assuming an instance of binderfs has been mounted at ``/dev/binderfs``, the
|
| D | hw_random.rst | 35 data before assuming it is truly random.
|
| /Documentation/block/ |
| D | switching-sched.rst | 11 assuming that you have sysfs mounted on /sys. If you don't have sysfs mounted,
|
| /Documentation/devicetree/bindings/phy/ |
| D | phy-rockchip-usbdp.yaml | 60 3>;", assuming DP lane0 on Type-C phy lane2, DP lane1 on Type-C phy
62 <0, 1, 2, 3>;", assuming DP lane0 on Type-C phy lane0, DP lane1 on Type-C
|
| /Documentation/ABI/testing/ |
| D | sysfs-memory-page-offline | 35 to access this page assuming it's poisoned by the
|
| D | sysfs-class-pktcdvd | 92 # assuming device pktcdvd0 was created, look at stat's
|
| /Documentation/devicetree/bindings/power/reset/ |
| D | gpio-poweroff.yaml | 51 description: Time to wait before assuming the power off sequence failed.
|
| /Documentation/mm/ |
| D | free_page_reporting.rst | 16 page reporting interface with the reporting framework assuming no other
|
| /Documentation/firmware-guide/acpi/ |
| D | gpio-properties.rst | 83 | +-------------+ as high, assuming non-active |
86 | | High | as high, assuming active |
89 | +-------------+ as low, assuming non-active |
92 | | Low | as low, assuming active |
332 Be aware that gpiod_get_index() in cases 1 and 2, assuming that there
|
| /Documentation/misc-devices/ |
| D | ad525x_dpot.rst | 37 So assuming the device in question is on the first i2c bus and has the slave
|
| /Documentation/gpu/rfc/ |
| D | i915_small_bar.h | 62 * small BAR configuration, assuming we are able to load
162 * possible to end up with a small BAR configuration, assuming we can
|
| /Documentation/filesystems/ |
| D | bfs.rst | 43 (assuming your root disk is on target=0, lun=0, bus=0, controller=0). Then you
|
| D | romfs.rst | 16 while romfs is less than a page, about 4000 bytes (assuming i586
86 (assuming bigendian quantities again). For details, please consult
|
| /Documentation/admin-guide/media/ |
| D | saa7134.rst | 61 options saa7134 card=13 # Assuming that your card type is #13
|
| /Documentation/iio/ |
| D | ep93xx_adc.rst | 19 Assuming ep93xx_adc is IIO device0, you'd find the following entries under
|
| /Documentation/leds/ |
| D | leds-class-multicolor.rst | 69 global 'brightness' control. Assuming a max_brightness of 255 the user
|
| /Documentation/userspace-api/media/v4l/ |
| D | vidioc-cropcap.rst | 72 Assuming pixel aspect 1/1 this could be for example a 640 × 480
|
| /Documentation/admin-guide/hw-vuln/ |
| D | cross-thread-rsb.rst | 44 to 2T mode, assuming the other thread is also still in C0 state.
|
123456