| /Documentation/devicetree/bindings/input/ |
| D | adc-joystick.yaml | 29 Each pair defines one ADC channel to which a joystick axis is connected.
51 "^axis@[0-9a-f]+$":
55 Represents a joystick axis bound to the given ADC channel.
56 For each entry in the io-channels list, one axis subnode with a matching
63 description: Index of an io-channels list entry bound to this axis.
66 description: EV_ABS specific event code generated by the axis.
74 Minimum and maximum values produced by the axis.
75 For an ABS_X axis this will be the left-most and right-most
77 treat the axis as inverted.
84 Omitting this property indicates the axis is precise.
[all …]
|
| D | rotary-encoder.yaml | 22 linux,axis:
25 the input subsystem axis to map to this rotary encoder.
33 encoder. Only relevant for absolute axis. Defaults to 24 which is a
36 rotary-encoder,relative-axis:
39 register a relative axis rather than an
40 absolute one. Relative axis will only generate +1/-1 events on the input
47 greater than the specified steps or smaller than 0. For absolute axis only.
86 linux,axis = <0>; /* REL_X */
88 rotary-encoder,relative-axis;
|
| D | gpio-decoder.txt | 11 - linux,axis: the input subsystem axis to map to (ABS_X/ABS_Y).
21 linux,axis = <0>; /* ABS_X */
|
| /Documentation/devicetree/bindings/crypto/ |
| D | artpec6-crypto.txt | 1 Axis crypto engine with PDMA interface.
5 "axis,artpec6-crypto" for the version in the Axis ARTPEC-6 SoC
6 "axis,artpec7-crypto" for the version in the Axis ARTPEC-7 SoC.
13 compatible = "axis,artpec6-crypto";
|
| /Documentation/devicetree/bindings/pci/ |
| D | axis,artpec6-pcie.txt | 1 * Axis ARTPEC-6 PCIe interface
7 - compatible: "axis,artpec6-pcie", "snps,dw-pcie" for ARTPEC-6 in RC mode;
8 "axis,artpec6-pcie-ep", "snps,dw-pcie" for ARTPEC-6 in EP mode;
9 "axis,artpec7-pcie", "snps,dw-pcie" for ARTPEC-7 in RC mode;
10 "axis,artpec7-pcie-ep", "snps,dw-pcie" for ARTPEC-7 in EP mode;
21 - axis,syscon-pcie: A phandle pointing to the ARTPEC-6 system controller,
27 compatible = "axis,artpec6-pcie", "snps,dw-pcie";
49 axis,syscon-pcie = <&syscon>;
|
| /Documentation/devicetree/bindings/arm/ |
| D | axis.txt | 1 Axis Communications AB
8 - compatible = "axis,artpec6";
13 - compatible = "axis,artpec6-dev-board", "axis,artpec6";
|
| /Documentation/devicetree/bindings/iio/accel/ |
| D | lis302.txt | 25 x/y/z axis.
28 x/y/z axis.
29 - st,click-thresh-{x,y,z}: set the x/y/z axis threshold
47 - st,wakeup-{x,y,z}-{lo,hi}: set wakeup condition on x/y/z axis for
50 - st,wakeup2-{x,y,z}-{lo,hi}: set wakeup condition on x/y/z axis for
59 - st,axis-{x,y,z}=: set the axis to map to the three coordinates.
60 Negative values can be used for inverted axis.
61 - st,{min,max}-limit-{x,y,z} set the min/max limits for x/y/z axis
|
| /Documentation/devicetree/bindings/clock/ |
| D | artpec6.txt | 1 * Clock bindings for Axis ARTPEC-6 chip
19 See dt-bindings/clock/axis,artpec6-clkctrl.h for the list of valid identifiers.
20 - compatible: Should be "axis,artpec6-clkctrl"
37 compatible = "axis,artpec6-clkctrl";
|
| /Documentation/devicetree/bindings/ |
| D | trivial-devices.yaml | 94 # DMARD05: 3-axis I2C Accelerometer
96 # DMARD06: 3-axis I2C Accelerometer
98 # DMARD05: 3-axis I2C Accelerometer
100 # DMARD09: 3-axis Accelerometer
102 # DMARD10: 3-axis Accelerometer
104 # MMA7660FC: 3-Axis Orientation/Motion Detection Sensor
106 # MMA8450Q: Xtrinsic Low-power, 3-axis Xtrinsic Accelerometer
192 # mCube 3-axis 8-bit digital accelerometer
212 # MEMSIC 3-axis accelerometer
214 # MEMSIC 2-axis 8-bit digital accelerometer
[all …]
|
| /Documentation/devicetree/bindings/input/touchscreen/ |
| D | bu21013.txt | 23 - rohm,touch-max-x : Maximum outward permitted limit in the X axis
24 - rohm,touch-max-y : Maximum outward permitted limit in the Y axis
25 - rohm,flip-x : Flip touch coordinates on the X axis
26 - rohm,flip-y : Flip touch coordinates on the Y axis
|
| D | touchscreen.yaml | 66 description: X axis is inverted
70 description: Y axis is inverted
74 description: X and Y axis are swapped
75 Swapping is done after inverting the axis
|
| D | ti,ads7843.yaml | 103 Swap x and y axis.
125 Maximum value on the X axis.
131 Minimum value on the X axis.
142 Maximum value on the Y axis.
148 Minimum value on the Y axis.
|
| D | hideep.txt | 15 - touchscreen-size-x : X axis size of touchscreen
16 - touchscreen-size-y : Y axis size of touchscreen
|
| /Documentation/devicetree/bindings/iio/ |
| D | mount-matrix.txt | 29 screen and (z) being depth, the axis perpendicular to the screen.
55 9.81 m/s^2 upwards along the (z) axis, i.e. out of the screen when the device
57 as the gravity vector is projected 1:1 onto the sensors (z)-axis.
78 its top towards surface, you get a negative y axis.
97 perpendicular to the North axis and positive towards the East and (z) is
131 device on a flat surface and spin it around the z axis (such as rotating a
133 along the (z) axis if rotated clockwise, and a positive value if rotated
189 The sensor is mounted 30 degrees (Pi/6 radians) tilted along the X axis, so we
190 compensate by performing a -30 degrees rotation around the X axis:
196 The sensor is flipped 180 degrees (Pi radians) around the Z axis, i.e. mounted
|
| /Documentation/input/joydev/ |
| D | joystick-api.rst | 57 __u8 number; /* axis/button number */
88 The values of ``number`` correspond to the axis or button that
90 is, you have both an axis 0 and a button 0). Generally,
93 Axis number
95 1st Axis X 0
96 1st Axis Y 1
97 2nd Axis X 2
98 2nd Axis Y 3
110 For an axis, ``value`` is a signed integer between -32767 and +32767
111 representing the position of the joystick along that axis. If you
[all …]
|
| D | joystick.rst | 156 * 2-axis, 4-button joystick
157 * 3-axis, 4-button joystick
158 * 4-axis, 4-button joystick
177 2btn 2-button n-axis joystick
178 y-joy Two 2-button 2-axis joysticks on an Y-cable
179 y-pad Two 2-button 2-axis gamepads on an Y-cable
183 gamepad 4/6-button n-axis gamepad
184 gamepad8 8-button 2-axis gamepad
195 0 Axis X1
196 1 Axis Y1
[all …]
|
| /Documentation/iio/ |
| D | adis16480.rst | 59 | 3-Axis Magnetometer related device files | Description …
63 | in_magn_x_calibbias | Calibration offset for the X-axis magnetometer channel…
65 | in_magn_x_filter_low_pass_3db_frequency | Bandwidth for the X-axis magnetometer channel. …
67 | in_magn_x_raw | Raw X-axis magnetometer channel value. …
69 | in_magn_y_calibbias | Calibration offset for the Y-axis magnetometer channel…
71 | in_magn_y_filter_low_pass_3db_frequency | Bandwidth for the Y-axis magnetometer channel. …
73 | in_magn_y_raw | Raw Y-axis magnetometer channel value. …
75 | in_magn_z_calibbias | Calibration offset for the Z-axis magnetometer channel…
77 | in_magn_z_filter_low_pass_3db_frequency | Bandwidth for the Z-axis magnetometer channel. …
79 | in_magn_z_raw | Raw Z-axis magnetometer channel value. …
[all …]
|
| D | adis16475.rst | 63 | 3-Axis Accelerometer related device files | Description …
67 | in_accel_x_calibbias | Calibration offset for the X-axis accelerometer chann…
69 | in_accel_x_raw | Raw X-axis accelerometer channel value. …
71 | in_accel_y_calibbias | Calibration offset for the Y-axis accelerometer chann…
73 | in_accel_y_raw | Raw Y-axis accelerometer channel value. …
75 | in_accel_z_calibbias | Calibration offset for the Z-axis accelerometer chann…
77 | in_accel_z_raw | Raw Z-axis accelerometer channel value. …
81 | in_deltavelocity_x_raw | Raw X-axis delta velocity channel value. …
83 | in_deltavelocity_y_raw | Raw Y-axis delta velocity channel value. …
85 | in_deltavelocity_z_raw | Raw Z-axis delta velocity channel value. …
[all …]
|
| /Documentation/input/devices/ |
| D | cma3000_d0x.rst | 17 CMA3000 Tri-axis accelerometer supports Motion detect, Measurement and
26 axis and supports 400, 100, 40 Hz sample frequency.
50 Noise on X Axis
53 Noise on Y Axis
56 Noise on Z Axis
|
| D | iforce-protocol.rst | 60 axis::
64 00 X-Axis lsb
65 01 X-Axis msb
66 02 Y-Axis lsb, or gas pedal for a wheel
67 03 Y-Axis msb, or brake pedal for a wheel
111 Bits 4-7: Val 2 = effect along one axis. Byte 05 indicates direction
112 Val 4 = X axis only. Byte 05 must contain 5a
113 Val 8 = Y axis only. Byte 05 must contain b4
128 08-09 Address of interactive parameters for X-axis,
130 0a-0b Address of interactive parameters for Y-axis,
[all …]
|
| /Documentation/input/ |
| D | multi-touch-protocol.rst | 88 total number of type B slots reported in the absinfo for the ABS_MT_SLOT axis.
90 The minimum value of the ABS_MT_SLOT axis must be 0.
215 and MINOR are the major and minor axis of an ellipse. The orientation of
235 The length of the major axis of the contact. The length should be given in
240 The length, in surface units, of the minor axis of the contact. If the
244 The length, in surface units, of the major axis of the approaching
250 The length, in surface units, of the minor axis of the approaching
276 the Y axis (north) of the surface, a negative value when the ellipse is
278 right. When aligned with the X axis in the positive direction, the range
279 max should be returned; when aligned with the X axis in the negative
[all …]
|
| /Documentation/devicetree/bindings/pinctrl/ |
| D | axis,artpec6-pinctrl.txt | 1 Axis ARTPEC-6 Pin Controller
4 - compatible: "axis,artpec6-pinctrl".
56 compatible = "axis,artpec6-pinctrl";
|
| /Documentation/devicetree/bindings/iio/imu/ |
| D | invensense,icm42600.yaml | 13 6-axis MotionTracking device that combines a 3-axis gyroscope and a 3-axis
|
| /Documentation/ABI/testing/ |
| D | sysfs-devices-platform-trackpoint | 21 (RW) Backup range for z-axis press.
29 z-axis pressed.
50 (RW) Minimum value for z-axis force required to trigger a press
59 select (click) on z-axis on release.
|
| /Documentation/devicetree/bindings/media/ |
| D | video-interface-devices.yaml | 36 read out, the X-axis points along the column read-out direction towards
37 the last columns, and the Y-axis along the row read-out direction towards
43 2591 X-axis 0
46 .......... ... ..........! Y-axis
54 placed on the top-left corner of the visible scene, the X-axis points
55 towards the right, and the Y-axis points towards the bottom of the scene.
62 0 X-axis
74 Y-axis
96 Y-axis
108 0 X-axis
|