Searched full:baud (Results 1 – 25 of 44) sorted by relevance
12
| /Documentation/devicetree/bindings/serial/ |
| D | nvidia,tegra20-hsuart.yaml | 58 nvidia,adjust-baud-rates:
61 List of entries providing percentage of baud rate adjustment within a range. Each entry
62 contains a set of 3 values: range low/high and adjusted rate. When the baud rate set on the
63 controller falls within the range mentioned in this field, the baud rate will be adjusted by
68 Increase baud rate by 2% when set baud rate falls within range 9600 to 115200.
70 Standard UART devices are expected to have tolerance for baud rate error by -4 to +4 %. All
72 issue. UART RX baud rate tolerance level is 0% to +4% in 1-stop config. Otherwise, the
74 baud rate to be higher than the deviations observed in TX.
77 valid range and Tegra baud rate has to be set above actual TX baud rate observed. To do this
78 we use nvidia,adjust-baud-rates.
[all …]
|
| D | serial-peripheral-props.yaml | 15 controller, might need similar properties, e.g. for configuring the baud
22 The maximum baud rate the device operates at.
26 baud rates.
31 The current baud rate the device operates at.
33 the baud rate of the slave device.
35 * device supports auto-baud
38 * device baud rate is configured by its firmware but there is no
|
| D | ingenic,uart.yaml | 47 - description: Baud clock
52 - const: baud
89 clock-names = "baud", "module";
|
| D | mediatek,uart.yaml | 17 with 16550A, with enhancements for high speed baud rates and
67 - const: baud
120 clock-names = "baud", "bus";
|
| D | fsl-lpuart.yaml | 54 - description: baud clock
60 - const: baud
|
| D | arm_sbsa_uart.txt | 10 - current-speed: the (fixed) baud rate set by the firmware
|
| D | amlogic,meson-uart.yaml | 78 - const: baud
101 clock-names = "xtal", "pclk", "baud";
|
| D | arc-uart.txt | 8 - current-speed : baud rate for UART
|
| D | xlnx,opb-uartlite.yaml | 38 The fixed baud rate that the device was configured for.
|
| /Documentation/devicetree/bindings/w1/ |
| D | w1-uart.yaml | 18 baud-rate and transmitted byte, which corresponds to a 1-Wire read bit,
21 The default baud-rate for reset and presence detection is 9600 and for
22 a 1-Wire read or write operation 115200. In case the actual baud-rate
35 The baud rate for the 1-Wire reset and presence detect.
40 The baud rate for the 1-Wire write-0 cycle.
45 The baud rate for the 1-Wire write-1 and read cycle.
|
| /Documentation/devicetree/bindings/sound/ |
| D | serial-midi.yaml | 19 Can only be set to use standard baud rates corresponding to supported rates of the
20 parent serial device. If the standard MIDI baud of 31.25 kBaud is needed
22 configure the clocks of the parent serial device so that a requested baud of 38.4 kBaud
23 results in the standard MIDI baud rate, and set the 'current-speed' property to 38400 (default)
|
| /Documentation/w1/masters/ |
| D | w1-uart.rst | 21 combination of baud-rate and transmitted byte, which corresponds to a
25 the baud-rate 9600, i.e. 104.2 us per bit. The transmitted byte 0xf0 over
31 Similar for a 1-Wire read bit or write bit, which uses the baud-rate
36 The default baud-rate for reset and presence detection is 9600 and for
37 a 1-Wire read or write operation 115200. In case the actual baud-rate
|
| /Documentation/misc-devices/ |
| D | oxsemi-tornado.rst | 10 The baud rate produced by the baud generator is obtained from this input
16 determine the actual baud rate used. Baud rates from 15625000bps down
23 used for the divisor to obtain the requested baud rates by software that
41 Here are the figures for the standard and some non-standard baud rates
88 With the baud base set to 15625000 and the unsigned 16-bit UART_DIV_MAX
89 limitation imposed by ``serial8250_get_baud_rate`` standard baud rates
91 200bps requires the baud base to be divided by 78125 and that is beyond
108 the baud rate of 38400bps. Note that the value of 0 in TCR sets the
115 respectively. These parameters will set the baud rate for the serial
|
| /Documentation/devicetree/bindings/spi/ |
| D | spi_oc_tiny.txt | 8 - baud-width: width, in bits, of the programmable divider used to scale
11 The clock-frequency and baud-width properties are needed only if the divider
|
| /Documentation/devicetree/bindings/power/reset/ |
| D | qnap-poweroff.txt | 5 Orion5x SoCs. Sending the character 'A', at 19200 baud, tells the
8 Synology NAS devices use a similar scheme, but a different baud rate,
|
| /Documentation/ABI/testing/ |
| D | sysfs-platform-kim | 19 The maximum reliable baud-rate the host can support.
21 UART configurations, so the baud-rate needs to be set
44 configuring baud and install line discipline via this sysfs
|
| /Documentation/devicetree/bindings/net/can/ |
| D | rockchip,rk3568v2-canfd.yaml | 35 - const: baud
70 clock-names = "baud", "pclk";
|
| /Documentation/networking/device_drivers/hamradio/ |
| D | baycom.rst | 21 Its baud rate may be changed via the ``baud`` module parameter,
30 It only supports half duplex, and only 1200 baud. Its devices
46 ser12 This is a very simple 1200 baud AFSK modem. The modem consists only
54 par96 This is a modem for 9600 baud FSK compatible to the G3RUH standard.
|
| /Documentation/devicetree/bindings/net/bluetooth/ |
| D | mediatek,bluetooth.txt | 44 - current-speed: Current baud rate of the device whose defaults to 921600
69 clock-names = "baud", "bus";
|
| D | amlogic,w155s2-bt.yaml | 12 the standard H4 protocol via a 4-wire UART interface, with baud rates
|
| /Documentation/devicetree/bindings/soc/fsl/cpm_qe/cpm/ |
| D | brg.txt | 1 * Baud Rate Generators
|
| /Documentation/usb/ |
| D | usb-serial.rst | 167 - changing baud rates (up to 115200)
174 - changing baud rates ought to flush tx/rx to avoid mangled half characters
195 have been pretty thoroughly tested at various baud rates with 8-N-1
265 $PSRF100,<protocol>,<baud>,<databits>,<stopbits>,<parity>*CHECKSUM
275 The hid->com adapter can run at a maximum baud of 115200bps. Please note
325 - Baud rate 300-230400
458 and pilot-manager -daemon calls will work. Baud rates up to 115200
492 - Baud rates higher than 115200 are currently broken.
|
| /Documentation/devicetree/bindings/mfd/ |
| D | zii,rave-sp.txt | 16 - current-speed: Should be set to baud rate SP device is using
|
| /Documentation/admin-guide/ |
| D | braille-console.rst | 19 override the baud rate to 115200, etc.
|
| /Documentation/devicetree/bindings/clock/ |
| D | marvell,armada-3700-uart-clock.yaml | 18 - description: UART 2 Baud Rate Divisor Register
|
12