Home
last modified time | relevance | path

Searched +full:bl +full:- +full:name (Results 1 – 8 of 8) sorted by relevance

/Documentation/devicetree/bindings/pwm/
Dpwm.txt5 -----------------
8 with a property containing a 'pwm-list':
10 pwm-list ::= <single-pwm> [pwm-list]
11 single-pwm ::= <pwm-phandle> <pwm-specifier>
12 pwm-phandle : phandle to PWM controller node
13 pwm-specifier : array of #pwm-cells specifying the given PWM
18 An optional property "pwm-names" may contain a list of strings to label
19 each of the PWM devices listed in the "pwms" property. If no "pwm-names"
20 property is given, the name of the user node will be used as fallback.
23 "pwm-names" property to map the name of the PWM device requested by the
[all …]
/Documentation/devicetree/bindings/leds/backlight/
Dlp855x-backlight.yaml1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/leds/backlight/lp855x-backlight.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Artur Weber <aweber.kernel@gmail.com>
15 - ti,lp8550
16 - ti,lp8551
17 - ti,lp8552
18 - ti,lp8553
19 - ti,lp8555
[all …]
/Documentation/driver-api/backlight/
Dlp855x-driver.rst15 -----------
37 ------------------------
41 * name:
42 Backlight driver name. If it is not defined, default name is set.
68 .name = "lcd-bl",
/Documentation/devicetree/bindings/mfd/
Dams,as3711.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
15 two step-up DC/DC converters are defined.
26 Step-up converter configuration, to be used as a backlight source
31 const: ams,as3711-bl
33 su1-dev:
34 description: Framebuffer phandle for the first step-up converter
37 su1-max-uA:
[all …]
Dti-lmu.txt5 Name Child nodes
6 ------ ---------------------------------
14 - compatible: Should be one of:
20 - reg: I2C slave address.
28 - enable-gpios: A GPIO specifier for hardware enable pin.
29 - ramp-up-us: Current ramping from one brightness level to
31 Range from 2048 us - 117.44 s
32 - ramp-down-us: Current ramping from one brightness level to
34 Range from 2048 us - 117.44 s
35 - ti,brightness-resolution - This determines whether to use 8 bit brightness
[all …]
/Documentation/arch/loongarch/
Dintroduction.rst1 .. SPDX-License-Identifier: GPL-2.0
7 LoongArch is a new RISC ISA, which is a bit like MIPS or RISC-V. There are
8 currently 3 variants: a reduced 32-bit version (LA32R), a standard 32-bit
9 version (LA32S) and a 64-bit version (LA64). There are 4 privilege levels
22 ----
24 LoongArch has 32 GPRs ( ``$r0`` ~ ``$r31`` ); each one is 32-bit wide in LA32
25 and 64-bit wide in LA64. ``$r0`` is hard-wired to zero, and the other registers
26 are not architecturally special. (Except ``$r1``, which is hard-wired as the
27 link register of the BL instruction.)
30 the LoongArch ELF psABI spec, in :ref:`References <loongarch-references>`:
[all …]
/Documentation/trace/coresight/
Dcoresight.rst2 Coresight - HW Assisted Tracing on ARM
9 ------------
38 0 CPU 0<-->: C : 0 CPU 0<-->: C : : C : @ STM @ || System ||
39 |->0000000 : T : |->0000000 : T : : T :<--->@@@@@ || Memory ||
40 | #######<-->: I : | #######<-->: I : : I : @@@<-| ||||||||||||
43 | |->### | ! | |->### | ! | ! . | || DAP ||
49 *****************************************************************<-|
63 | * ===== F =====<---------|
65 |-->:: CTI ::<!! === N ===
69 |------>&& ETB &&<......II I =======
[all …]
/Documentation/admin-guide/
Dkernel-parameters.txt16 force -- enable ACPI if default was off
17 on -- enable ACPI but allow fallback to DT [arm64,riscv64]
18 off -- disable ACPI if default was on
19 noirq -- do not use ACPI for IRQ routing
20 strict -- Be less tolerant of platforms that are not
22 rsdt -- prefer RSDT over (default) XSDT
23 copy_dsdt -- copy DSDT to memory
24 nospcr -- disable console in ACPI SPCR table as
41 If set to vendor, prefer vendor-specific driver
73 Documentation/firmware-guide/acpi/debug.rst for more information about
[all …]