Searched full:brackets (Results 1 – 25 of 45) sorted by relevance
12
| /Documentation/ABI/testing/ |
| D | sysfs-driver-aspeed-uart-routing | 8 selected option marked by brackets "[]". The list of available options
25 will be marked by brackets "[]".
|
| D | sysfs-driver-hid-picolcd | 8 enclosed in brackets ('[' and ']')
34 the active refresh rate being enclosed in brackets ('[' and ']')
|
| D | sysfs-bus-iio-dac-dpot-dac | 7 the step and the maximum value, all enclosed in square brackets.
|
| D | sysfs-bus-iio-potentiometer-mcp4531 | 7 the step and the maximum value, all enclosed in square brackets.
|
| D | sysfs-driver-typec-displayport | 10 with the active one wrapped in square brackets.
33 square brackets.
|
| D | sysfs-bus-iio-distance-srf08 | 13 in square brackets.
|
| D | sysfs-bus-iio-sps30 | 28 square brackets.
|
| D | sysfs-class-rc | 28 Enabled protocols are shown in [] brackets.
89 The enabled wakeup protocol is shown in [] brackets.
|
| D | sysfs-class-typec | 13 KOBJ_CHANGE on the port. The current role is show in brackets,
28 KOBJ_CHANGE. The current role is show in brackets, for example
150 brackets. Selection happens by writing to the file.
|
| /Documentation/devicetree/bindings/ |
| D | .yamllint | 19 brackets:
|
| /Documentation/block/ |
| D | switching-sched.rst | 29 will be displayed, with the currently selected scheduler in brackets::
|
| /Documentation/userspace-api/media/rc/ |
| D | rc-sysfs-nodes.rst | 41 Enabled protocols are shown in [] brackets.
102 The enabled wakeup protocol is shown in [] brackets.
|
| /Documentation/devicetree/bindings/opp/ |
| D | opp-v2-base.yaml | 70 by angular brackets <>. The OPP binding doesn't provide any provisions to
94 separated by angular brackets <>. If current values aren't required
109 separated by angular brackets <>. If power values aren't required
|
| /Documentation/maintainer/ |
| D | modifying-patches.rst | 16 name, all enclosed in square brackets, is noticeable enough to make it obvious
|
| /Documentation/gpu/ |
| D | msm-crash-dump.rst | 87 by brackets { }.
|
| /Documentation/devicetree/bindings/display/ |
| D | allwinner,sun4i-a10-display-engine.yaml | 37 within the square brackets corresponds to the ID of the local endpoint.
|
| /Documentation/process/ |
| D | maintainer-tip.rst | 248 brackets after the function name can be ambiguous::
254 The variant with brackets is more precise::
626 Brackets should be omitted only if the statement which follows 'if', 'for',
633 though C does not require brackets::
639 Adding brackets around the outer loop enhances the reading flow::
|
| /Documentation/admin-guide/ |
| D | cputopology.rst | 55 source for the output is in brackets ("[]").
|
| /Documentation/devicetree/bindings/pinctrl/ |
| D | marvell,orion-pinctrl.txt | 17 Note: brackets (x) are not part of the mpp name for marvell,function and given
|
| D | marvell,dove-pinctrl.txt | 12 Note: brackets (x) are not part of the mpp name for marvell,function and given
|
| D | marvell,armada-375-pinctrl.txt | 11 Note: brackets (x) are not part of the mpp name for marvell,function and given
|
| D | marvell,armada-370-pinctrl.txt | 11 Note: brackets (x) are not part of the mpp name for marvell,function and given
|
| D | marvell,armada-xp-pinctrl.txt | 14 Note: brackets (x) are not part of the mpp name for marvell,function and given
|
| /Documentation/admin-guide/pm/ |
| D | sleep-states.rst | 192 shown in square brackets.
238 The currently selected option is shown in square brackets, which means
|
| /Documentation/devicetree/bindings/arm/marvell/ |
| D | ap80x-system-controller.txt | 46 Note: brackets (x) are not part of the mpp name for marvell,function and given
|
12