Searched full:calculate (Results 1 – 25 of 109) sorted by relevance
12345
| /Documentation/driver-api/media/drivers/ |
| D | sh_mobile_ceu_camera.rst | 72 1. Calculate current sensor scales:
76 2. Calculate "effective" input crop (sensor subwindow) - CEU crop scaled back at
81 3. Calculate new combined scales from "effective" input window to requested user
86 4. Calculate sensor output window by applying combined scales to real input
97 7. Calculate new sensor scales:
101 8. Calculate new CEU crop - apply sensor scales to previously calculated
137 4. Sensor scaled to 3 : 3'. Sensor's scale is (2' - 2) / (3' - 3). Calculate
140 5. Calculate and apply host scale = (6' - 6) / (4' - 4)
142 6. Calculate and apply host crop: 6 - 7 = (5 - 2) * (6' - 6) / (5' - 5)
|
| /Documentation/hwmon/ |
| D | ltc4260.rst | 44 registers. If a set of voltage divider resistors is installed, calculate the
51 is installed. If a different sense resistor is installed, calculate the real
|
| D | ltc4261.rst | 44 registers. If a set of voltage divider resistors is installed, calculate the
51 is installed. If a different sense resistor is installed, calculate the real
|
| D | ltc2945.rst | 44 registers. If a set of voltage divider resistors is installed, calculate the
51 is installed. If a different sense resistor is installed, calculate the real
|
| D | fam15h_power.rst | 62 calculate the average power consumed by a processor during a
110 v. Calculate the average power consumption for a compute unit over
|
| D | vexpress.rst | 33 temperature and power usage. Some of them also calculate consumed energy
|
| D | tmp513.rst | 85 register value. Those values are calculate by the hardware using those
|
| /Documentation/ABI/testing/ |
| D | sysfs-cfq-target-latency | 8 use it to calculate the time slice used for every task.
|
| D | sysfs-bus-iio-adc-pac1934 | 8 Y is the channel number. The value is used to calculate
|
| D | sysfs-driver-w1_ds28e17 | 18 Description: When written, this file sets the multiplier used to calculate
|
| /Documentation/devicetree/bindings/iio/dac/ |
| D | adi,ad7303.yaml | 21 Used to calculate output channel scalling if REF-supply not specified.
|
| /Documentation/devicetree/bindings/iio/impedance-analyzer/ |
| D | adi,ad5933.yaml | 29 are connected together. Used to calculate voltage scaling of measurement
|
| /Documentation/networking/ |
| D | 6lowpan.rst | 10 The priv_size of each interface should be calculate by::
|
| /Documentation/admin-guide/perf/ |
| D | hns3-pmu.rst | 49 calculate real performance data in userspace.
57 computation to calculate real performance data is:::
|
| /Documentation/devicetree/bindings/mfd/ |
| D | mxs-lradc.txt | 14 - fsl,ave-ctrl: number of samples per direction to calculate an average value.
|
| /Documentation/driver-api/thermal/ |
| D | power_allocator.rst | 202 allocator governor to calculate how much power to give to each cooling
222 on failure. This is currently used by thermal core to calculate the
237 Calculate a cooling device state that would make the device consume at
|
| /Documentation/usb/ |
| D | misc_usbsevseg.rst | 47 to set the nth decimal place calculate 10 ** n
|
| /Documentation/security/tpm/ |
| D | tpm_event_log.rst | 45 before the Linux EFI stub gets to run. Thus, it needs to calculate and save the
|
| /Documentation/devicetree/bindings/media/i2c/ |
| D | dongwoon,dw9768.yaml | 61 factor to calculate VCM ring periodic time Tvib.
|
| /Documentation/w1/masters/ |
| D | omap-hdq.rst | 36 be used to calculate the CRC and pass back an appropriate slave ID to the W1
|
| /Documentation/devicetree/bindings/gpio/ |
| D | socionext,uniphier-gpio.yaml | 97 // UNIPHIER_GPIO_PORT() is a helper macro to calculate 29 * 8 + 4.
|
| /Documentation/devicetree/bindings/hwmon/ |
| D | adi,ltc2947.yaml | 36 calculate charge and energy so that, they can be only accumulated for
|
| /Documentation/userspace-api/media/v4l/ |
| D | colorspaces.rst | 42 can take an SPD and calculate the stimulus for each color receptor.
140 encoding and the colorspace. From that information you can calculate the
|
| /Documentation/trace/ |
| D | uprobetracer.rst | 19 user to calculate the offset of the probepoint in the object.
126 .. note:: User has to explicitly calculate the offset of the probe-point
|
| /Documentation/admin-guide/ |
| D | cpu-load.rst | 6 ``/proc/uptime`` that userland tools, such as top(1), use to calculate
|
12345