Searched full:calculated (Results 1 – 25 of 172) sorted by relevance
1234567
| /Documentation/hwmon/ |
| D | da9052.rst | 48 The battery voltage is calculated as:
52 The backup battery voltage is calculated as:
56 The voltages on ADC channels 4, 5 and 6 are calculated as:
66 The junction temperature is calculated:
72 The battery temperature is calculated:
|
| D | da9055.rst | 39 The system voltage is calculated as:
43 The voltages on ADC channels 1, 2 and 3 are calculated as:
53 The junction temperature is calculated:
|
| D | fam15h_power.rst | 36 be calculated using different processor northbridge function
55 On multi-node processors the calculated value is for the entire
|
| D | wm831x.rst | 35 are available. The chip temperature is calculated as:
|
| /Documentation/arch/arm/nwfpe/ |
| D | notes.rst | 14 I was looking at some code, that calculated a double result, stored it in f4
30 The result of log(x) (a double) will be calculated, returned in f0, then
|
| /Documentation/ABI/testing/ |
| D | sysfs-class-led-driver-aw200xx | 4 "auto", the dim will be calculated according to the
|
| D | sysfs-class-fpga-region | 7 is defined or calculated by the layer that is creating the
|
| D | sysfs-class-led | 14 LEDs within the group to a calculated percentage of what
17 The percentage is calculated for each grouped LED via
|
| D | sysfs-bus-iio-health-afe440x | 19 calculated difference in the value of stage 1 - 2 and 3 - 4.
|
| /Documentation/driver-api/cxl/ |
| D | access-coordinates.rst | 64 endpoint CDAT and the upstream link bandwidth is calculated. If the endpoint
65 has a CXL switch as a parent, then min() of calculated bandwidth and the
67 with the endpoint is calculated. The final bandwidth is stored in a
|
| /Documentation/devicetree/bindings/leds/ |
| D | skyworks,aat1290.yaml | 41 Maximum flash LED supply current can be calculated using following
46 Maximum flash timeout can be calculated using following formula::
|
| D | richtek,rt8515.yaml | 60 ground. The maximum hardware current setting is calculated
72 ground. The maximum hardware current setting is calculated
|
| /Documentation/devicetree/bindings/clock/ |
| D | renesas,rzv2h-cpg.yaml | 42 a module number. The module number is calculated as the CLKON register
54 is calculated as the reset register offset index multiplied by 16, plus the
|
| D | brcm,bcm53573-ilp.txt | 10 ILP's rate has to be calculated on runtime and it depends on ALP clock
|
| D | st,stm32-rcc.txt | 45 It is calculated as: index = register_offset / 4 * 32 + bit_offset.
129 It is calculated as: index = register_offset / 4 * 32 + bit_offset.
|
| /Documentation/misc-devices/ |
| D | apds990x.rst | 29 only lux values. Lux value is calculated using information from the both
30 channels. HW threshold level is calculated from the given lux value to match
|
| /Documentation/sound/designs/ |
| D | tracepoints.rst | 92 decided as a fixed number, this value is also calculated according to
98 decided as a single value, this value is also calculated according to
105 also calculated according to it. Else, zero. But this behaviour depends
|
| /Documentation/networking/device_drivers/cellular/qualcomm/ |
| D | rmnet.rst | 95 Valid bit indicates whether the partial checksum is calculated and is valid.
152 implies that checksum is calculated on this packet and is valid, value of 0
153 indicates that the calculated packet checksum is invalid.
|
| /Documentation/admin-guide/device-mapper/ |
| D | dm-service-time.rst | 52 which is calculated by::
71 If calculated service time is equal, the path having maximum
|
| /Documentation/filesystems/ext4/ |
| D | overview.rst | 10 ``sb.s_blocks_per_group`` blocks, though it can also calculated as 8 *
|
| D | about.rst | 29 actual size is calculated as 2 ^ (10 + ``sb.s_log_block_size``) bytes.
|
| /Documentation/devicetree/bindings/sound/ |
| D | maxim,max98390.yaml | 21 description: The calculated temperature data was measured while doing the calibration.
|
| /Documentation/userspace-api/media/dvb/ |
| D | fe-read-uncorrected-blocks.rst | 39 calculated. For this command, read-only access to the device is
|
| /Documentation/devicetree/bindings/net/can/ |
| D | cc770.txt | 29 a reasonable value will be calculated.
|
| /Documentation/driver-api/media/ |
| D | tx-rx.rst | 65 The pixel rate on the bus is calculated as follows::
90 The pixel rate calculated this way is **not** the same thing as the
|
1234567