Searched +full:cap +full:- +full:power +full:- +full:off +full:- +full:card (Results 1 – 5 of 5) sorted by relevance
| /Documentation/devicetree/bindings/mmc/ |
| D | mmc-controller.yaml | 1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/mmc/mmc-controller.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Ulf Hansson <ulf.hansson@linaro.org>
25 "#address-cells":
30 "#size-cells":
33 # Card Detection.
34 # If none of these properties are supplied, the host native card
37 broken-cd:
[all …]
|
| D | usdhi6rol0.txt | 5 - compatible: must be
7 - interrupts: 3 interrupts, named "card detect", "data" and "SDIO" must be
9 - clocks: a clock binding for the IMCLK input
13 - vmmc-supply: a phandle of a regulator, supplying Vcc to the card
14 - vqmmc-supply: a phandle of a regulator, supplying VccQ to the card
15 - pinctrl-names: Can contain a "default" entry and a "state_uhs"
19 - pinctrl-N: One property for each name listed in pinctrl-names, see
20 ../pinctrl/pinctrl-bindings.txt.
32 interrupt-names = "card detect", "data", "SDIO";
33 bus-width = <4>;
[all …]
|
| /Documentation/devicetree/bindings/net/wireless/ |
| D | ti,wl1251.txt | 7 - compatible : Should be "ti,wl1251"
8 - reg : Chip select address of device
9 - spi-max-frequency : Maximum SPI clocking speed of device in Hz
10 - interrupts : Should contain interrupt line
11 - vio-supply : phandle to regulator providing VIO
14 - ti,wl1251-has-eeprom : boolean, the wl1251 has an eeprom connected, which
16 - ti,power-gpio : GPIO connected to chip's PMEN pin if operated in
18 - Please consult Documentation/devicetree/bindings/spi/spi-bus.txt
28 spi-max-frequency = <48000000>;
29 spi-cpol;
[all …]
|
| D | ti,wlcore.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Tony Lindgren <tony@atomide.com>
14 Note that the *-clock-frequency properties assume internal clocks. In case
21 - ti,wl1271
22 - ti,wl1273
23 - ti,wl1281
24 - ti,wl1283
25 - ti,wl1285
[all …]
|
| /Documentation/devicetree/bindings/net/ |
| D | marvell-bt-8xxx.txt | 2 ------
9 - compatible : should be one of the following:
10 * "marvell,sd8897-bt" (for SDIO)
11 * "marvell,sd8997-bt" (for SDIO)
16 - marvell,cal-data: Calibration data downloaded to the device during
20 - marvell,wakeup-pin: It represents wakeup pin number of the bluetooth chip.
22 - marvell,wakeup-gap-ms: wakeup gap represents wakeup latency of the host
25 - interrupt-names: Used only for USB based devices (See below)
26 - interrupts : specifies the interrupt pin number to the cpu. For SDIO, the
29 named "wakeup" from the interrupt-names and interrupt arrays.
[all …]
|