Searched full:configuring (Results 1 – 25 of 171) sorted by relevance
1234567
| /Documentation/admin-guide/cgroup-v1/ |
| D | net_cls.rst | 33 - configuring tc::
42 configuring iptables, basic example::
|
| /Documentation/devicetree/bindings/mmc/ |
| D | sdhci-st.txt | 9 to set the internal glue logic used for configuring the MMC
34 - non-removable: Non-removable slot. Also used for configuring mmcss in STiH407 SoC
42 configuring the CCONFIG3 in the mmcss.
|
| /Documentation/devicetree/bindings/phy/ |
| D | ti,phy-am654-serdes.yaml | 44 description: Phandle to the SYSCON entry required for configuring SERDES clock selection.
52 description: Phandle to the SYSCON entry required for configuring SERDES lane function.
|
| D | phy-cpcap-usb.txt | 16 mode-gpios: Optional GPIOs for configuring alternate modes
|
| /Documentation/devicetree/bindings/memory-controllers/fsl/ |
| D | fsl,imx-weim-peripherals.yaml | 17 configuring the WEIM settings/timings and will accompany the bindings
|
| /Documentation/ABI/testing/ |
| D | sysfs-class-vduse | 7 framework and provides a sysfs interface for configuring
|
| D | sysfs-platform-kim | 44 configuring baud and install line discipline via this sysfs
|
| /Documentation/devicetree/bindings/hwmon/ |
| D | ltc2990.txt | 7 An array of two integers for configuring the chip measurement mode.
|
| /Documentation/admin-guide/nfs/ |
| D | nfs-idmapper.rst | 14 type, see the "Configuring" section below if you wish to use the request-key
23 Configuring chapter
|
| /Documentation/devicetree/bindings/serial/ |
| D | serial-peripheral-props.yaml | 15 controller, might need similar properties, e.g. for configuring the baud
|
| /Documentation/userspace-api/media/drivers/ |
| D | camera-sensor.rst | 44 intervals as well as configuring the frame interval. Which one to implement
75 be followed by other entities that are there to allow configuring binning,
|
| /Documentation/devicetree/bindings/net/ |
| D | microchip,lan78xx.txt | 14 - microchip,led-modes: a 0..4 element vector, with each element configuring
|
| D | xlnx,gmii-to-rgmii.yaml | 19 different speed modes by configuring the converter register through mdio write.
|
| /Documentation/devicetree/bindings/i2c/ |
| D | i2c-opal.txt | 5 used by the firmware itself for configuring the port. From the linux
|
| /Documentation/networking/ |
| D | alias.rst | 39 Alias (re-)configuring
|
| D | bonding.rst | 47 3. Configuring Bonding Devices
50 3.1.2 Configuring Multiple Bonds with Sysconfig
53 3.2.2 Configuring Multiple Bonds with Initscripts
54 3.3 Configuring Bonding Manually with Ifenslave
55 3.3.1 Configuring Multiple Bonds Manually
56 3.4 Configuring Bonding Manually via Sysfs
59 3.7 Configuring LACP for 802.3ad mode in a more secure way
71 7.2 Configuring Multiple ARP Targets
83 11. Configuring Bonding for High Availability
89 12. Configuring Bonding for Maximum Throughput
[all …]
|
| /Documentation/networking/device_drivers/ethernet/freescale/ |
| D | gianfar.rst | 26 configuring VLANs. The gianfar driver supports hardware insertion and
|
| /Documentation/driver-api/gpio/ |
| D | intro.rst | 58 a LED, configuring a transceiver, bit-banging a serial bus, poking a hardware
104 high signal and configuring the GPIO as input for low. This open drain/open
|
| /Documentation/cpu-freq/ |
| D | cpufreq-stats.rst | 16 3. Configuring cpufreq-stats
117 3. Configuring cpufreq-stats
|
| /Documentation/userspace-api/media/mediactl/ |
| D | media-controller-model.rst | 8 Discovering a device internal topology, and configuring it at runtime,
|
| /Documentation/devicetree/bindings/media/i2c/ |
| D | adv7343.txt | 19 - ad,adv7343-power-mode-dac: array configuring the power on/off DAC's 1..6,
|
| /Documentation/devicetree/bindings/pci/ |
| D | ti,am65-pci-ep.yaml | 40 description: Phandle to the SYSCON entry required for configuring PCIe in RC or EP mode.
|
| /Documentation/userspace-api/media/v4l/ |
| D | dev-subdev.rst | 97 responsible for configuring every block in the video pipeline according
132 Applications are responsible for configuring coherent parameters on the
562 selections. The order of configuring formats and selections along a stream is
598 Configuring streams
605 There are three steps in configuring the streams:
685 After configuring routing, the next step is configuring the formats and
|
| /Documentation/usb/ |
| D | gadget_uvc.rst | 23 Configuring the device kernel
28 Configuring the gadget through configfs
209 Configuring an extension unit involves creating an entry in the appropriate
278 Configuring Supported Controls for Camera Terminal and Processing Unit
|
| /Documentation/devicetree/bindings/net/wireless/ |
| D | qca,ath9k.yaml | 13 This node provides properties for configuring the ath9k wireless device.
|
1234567