Searched full:correctly (Results 1 – 25 of 284) sorted by relevance
12345678910>>...12
| /Documentation/admin-guide/device-mapper/ |
| D | dm-flakey.rst | 44 Write I/O is handled correctly.
48 Read I/O is handled correctly.
52 Read I/O is handled correctly.
|
| /Documentation/devicetree/bindings/serial/ |
| D | arc-uart.txt | 20 Note: Each port should have an alias correctly numbered in "aliases" node.
|
| D | digicolor-usart.txt | 14 Note: Each UART port should have an alias correctly numbered
|
| D | cirrus,clps711x-uart.txt | 14 Note: Each UART port should have an alias correctly numbered
|
| /Documentation/devicetree/bindings/gpio/ |
| D | gpio-clps711x.txt | 14 Note: Each GPIO port should have an alias correctly numbered in "aliases"
|
| /Documentation/devicetree/bindings/timer/ |
| D | cirrus,clps711x-timer.txt | 9 Note: Each timer should have an alias correctly numbered in "aliases" node.
|
| /Documentation/admin-guide/ |
| D | edid.rst | 11 either correctly working because all components follow the standards -
|
| /Documentation/dev-tools/kunit/ |
| D | run_manual.rst | 99 For test authors, to use this feature, tests will need to correctly initialise
100 and/or clean up any data, so the test runs correctly a second time.
|
| /Documentation/devicetree/bindings/net/ |
| D | ti,dp83822.yaml | 45 correctly or not set at all then this boolean can be used to enable it.
92 If the strap pin is not set correctly or not set at all, then this can be
|
| D | mdio-gpio.yaml | 36 # Note: Each gpio-mdio bus should have an alias correctly numbered in "aliases"
|
| /Documentation/litmus-tests/locking/ |
| D | DCL-broken.litmus | 7 * correctly implement double-checked locking.
|
| /Documentation/devicetree/bindings/phy/ |
| D | bcm-ns-usb2-phy.yaml | 10 To initialize USB 2.0 PHY driver needs to setup PLL correctly.
|
| /Documentation/filesystems/iomap/ |
| D | porting.rst | 102 they should largely be debugged and working correctly after this step.
106 The mapping functions should all work correctly, so all that needs to be
|
| /Documentation/i2c/ |
| D | fault-codes.rst | 22 to respond correctly. Other code may need to rely on YOUR code reporting
23 the right fault code, so that it can (in turn) behave correctly.
|
| /Documentation/devicetree/bindings/pinctrl/ |
| D | brcm,ns-pinmux.yaml | 16 system configure controller correctly.
|
| /Documentation/arch/s390/ |
| D | 3270.ChangeLog | 18 * Do read and write lengths correctly in fs3270_read()
|
| /Documentation/driver-api/media/drivers/ |
| D | bttv-devel.rst | 14 To handle the grabber boards correctly, there is a array tvcards[] in
39 Of course you need a correctly installed soundcard unless you have the
|
| /Documentation/driver-api/ |
| D | console.rst | 148 The current crop of console drivers should still work correctly, but binding
150 be made to work correctly.
|
| /Documentation/PCI/ |
| D | acpi-info.rst | 28 can work correctly even on a system with new devices unknown to the OS.
35 is defined, an old OS needs to operate correctly even though it ignores the
57 BIOSes didn't use that bit correctly. The result is that the current ACPI
|
| /Documentation/devicetree/bindings/sound/ |
| D | ti,ts3a227e.yaml | 15 switches automatically to route the microphone correctly. It also
|
| /Documentation/hwmon/ |
| D | nsa320.rst | 35 that contains 0x55 as a marker to indicate that data is being read correctly,
|
| /Documentation/ABI/testing/ |
| D | configfs-usb-gadget-mass-storage | 10 correctly. You should set it to true.
|
| /Documentation/arch/x86/ |
| D | kernel-stacks.rst | 95 To handle nested #DB correctly there exist two instances of DB stacks. On
139 entries), regardless of whether the frame pointer was set up correctly
|
| /Documentation/userspace-api/media/v4l/ |
| D | ext-ctrls-dv.rst | 85 standard correctly (unfortunately quite common for HDMI and DVI-D).
144 standard correctly (unfortunately quite common for HDMI and DVI-D).
|
| /Documentation/trace/coresight/ |
| D | coresight-perf.rst | 19 is working correctly. You can dump the content of this file as
41 correctly.
|
12345678910>>...12