Searched full:currents (Results 1 – 25 of 25) sorted by relevance
| /Documentation/sphinx/templates/ |
| D | kernel-toc.html | 14 let currents = document.getElementsByClassName("current")
15 if (currents.length) {
16 sbar.scrollTop = currents[currents.length - 1].offsetTop;
|
| /Documentation/devicetree/bindings/iio/adc/ |
| D | adi,ad7192.yaml | 97 adi,burnout-currents-enable:
100 path are enabled. When BURN = 0, the burnout currents are disabled.
101 The burnout currents can be enabled only when the buffer is active
206 adi,burnout-currents-enable;
|
| /Documentation/devicetree/bindings/hwmon/ |
| D | adi,ltc2991.yaml | 14 The LTC2991 is used to monitor system temperatures, voltages and currents.
46 The channel number. LTC2991 can monitor 4 currents/temperatures.
|
| /Documentation/hwmon/ |
| D | tmp513.rst | 56 The driver exports the shunt currents values via the following sysFs files:
84 The bus power and bus currents range and resolution depends on the calibration
|
| D | mc34vr500.rst | 20 monitors the temperature, input voltage and output currents and provides
|
| D | ltc2991.rst | 27 The LTC2991 is used to monitor system temperatures, voltages and currents.
|
| D | vexpress.rst | 32 providing information about power lines voltages and currents, board
|
| D | adp1050.rst | 29 conversion used to monitor system temperatures, voltages and currents.
|
| D | adm1275.rst | 90 or current scaling. Reported voltages, currents, and power are raw measurements,
|
| D | sysfs-interface.rst | 316 Currents section in Attribute access
360 Also see the Alarms section for status flags associated with currents.
|
| /Documentation/devicetree/bindings/hwmon/pmbus/ |
| D | adi,adp1050.yaml | 13 The ADP1050 is used to monitor system voltages, currents and temperatures.
|
| /Documentation/devicetree/bindings/power/supply/ |
| D | x-powers,axp20x-battery-power-supply.yaml | 11 currents of the battery by reading ADC channels from the ADC.
|
| /Documentation/devicetree/bindings/leds/ |
| D | qcom,pm8058-led.yaml | 19 Hardware-wise the different LEDs support slightly different output currents.
|
| D | leds-lm3532.txt | 7 method allows for different LED currents in each current sink thus allowing
|
| /Documentation/sound/soc/ |
| D | overview.rst | 24 power via changing codec oversampling rates, bias currents, etc.
|
| /Documentation/devicetree/bindings/regulator/ |
| D | gpio-regulator.yaml | 57 description: Selection of available voltages/currents provided by this
|
| /Documentation/leds/ |
| D | leds-lm3556.rst | 22 from 93.75 mA to 1500 mA.The Flash currents are adjusted via the CURRENT
|
| /Documentation/devicetree/bindings/iio/dac/ |
| D | adi,ltc2672.yaml | 79 ADC channel to monitor voltages and currents at the MUX pin.
|
| /Documentation/devicetree/bindings/mfd/ |
| D | rohm,bd71828-pmic.yaml | 62 BD71827 and BD71828 have SAR ADC for measuring charging currents.
|
| D | rohm,bd71815-pmic.yaml | 57 BD71815 has SAR ADC for measuring charging currents. External sense
|
| /Documentation/driver-api/ |
| D | regulator.rst | 99 interface for this. Both take ranges of voltages and currents, supporting
|
| /Documentation/power/ |
| D | power_supply_class.rst | 51 All voltages, currents, charges, energies, time and temperatures in µV,
|
| /Documentation/core-api/ |
| D | kernel-api.rst | 376 called a *retention mode*. This mode still incurs leakage currents,
|
| /Documentation/input/devices/ |
| D | joystick-parport.rst | 74 port), and combine the currents of two or more data bits together::
|
| /Documentation/ABI/testing/ |
| D | sysfs-bus-iio | 832 of a different type. E.g. LED currents.
|