Searched full:displayed (Results 1 – 25 of 103) sorted by relevance
12345
| /Documentation/ABI/testing/ |
| D | sysfs-platform-dell-smbios | 21 displayed.
|
| D | sysfs-class-spi-eeprom | 16 present. It will be displayed as a 8 byte hex string, as read
|
| D | sysfs-firmware-qemu_fw_cfg | 31 The only legacy blob displayed is the fw_cfg device revision:
38 displayed as entries named after their unique selector key
|
| D | sysfs-bus-iio-isl29501 | 47 The value stored in sensor is displayed when read from.
|
| D | debugfs-driver-qat_telemetry | 91 counters are displayed::
95 If ``control`` is 2, 3 or 4, counters are displayed in the
153 counters are displayed::
157 If ``control`` is 2, 3 or 4, counters are displayed in the
|
| /Documentation/admin-guide/media/ |
| D | bt8xx.rst | 94 1: only error messages are displayed
95 2: notifications are displayed
96 3: other useful messages are displayed
|
| /Documentation/ABI/stable/ |
| D | sysfs-class-tpm | 61 Here the short, medium and long durations are displayed in
62 usecs. "[original]" indicates that the values are displayed
66 scaled to be displayed in usecs. In this case "[adjusted]"
67 will be displayed in place of "[original]".
|
| /Documentation/arch/x86/ |
| D | cpuinfo.rst | 89 displayed accordingly in /proc/cpuinfo. For example, the flag "avx2"
114 "split_lock_detect" will be displayed. The flag "ring3mwait" will be
115 displayed only when running on INTEL_XEON_PHI_[KNL|KNM] processors.
146 There are situations in which overriding the displayed name of the flag is
166 problem enabling the feature at run time, the flag will not be displayed.
|
| /Documentation/admin-guide/ |
| D | lockup-watchdogs.rst | 11 stack trace is displayed upon detection and, by default, the system
21 Similarly to the softlockup case, the current stack trace is displayed
|
| D | svga.rst | 40 mode list displayed may vary as the kernel version changes, because the
41 modes are listed in a "first detected -- first displayed" manner. It's
44 0x.... - Hexadecimal video mode ID (also displayed on the menu, see below
89 The modes displayed on the menu are partially sorted: The list starts with
147 but it relies on the mode being found and displayed on the menu
|
| /Documentation/userspace-api/media/v4l/ |
| D | selection-api-intro.rst | 22 select the part of display where the image should be displayed. The size
|
| D | dev-overlay.rst | 99 pixel is displayed, otherwise a pixel of the graphics surface.
103 video is displayed, so the graphics surface can be seen here.
223 displayed only when the bit is *set*. Pixel coordinates translate to
267 clipping rectangles are displayed.
|
| D | func-write.rst | 46 video frame, raw VBI image, sliced VPS or WSS data is displayed again.
|
| D | pixfmt-intro.rst | 20 images to the X Windows screen format when the video is to be displayed.
|
| D | func-select.rst | 52 buffer has been filled or displayed and can be dequeued with the
|
| /Documentation/block/ |
| D | switching-sched.rst | 29 will be displayed, with the currently selected scheduler in brackets::
|
| /Documentation/devicetree/bindings/display/panel/ |
| D | panel-common.yaml | 26 Specifies the width of the physical area where images are displayed. This
31 Specifies the height of the physical area where images are displayed. This
|
| /Documentation/filesystems/ |
| D | efivarfs.rst | 30 displayed, for example using "hexdump", pay attention that the first
|
| /Documentation/scsi/ |
| D | advansys.rst | 72 driver. If an assertion fails a message will be displayed to
128 This will cause printk() messages to be displayed on the
165 This information can be displayed with cat. For example::
|
| /Documentation/networking/device_drivers/ethernet/neterion/ |
| D | s2io.rst | 47 In case of Xframe II, the PCI/PCI-X bus width and frequency are displayed
70 e. Statistics. Comprehensive MAC-level and software statistics displayed
|
| /Documentation/arch/arm/ |
| D | setup.rst | 52 all the bootup messages to be displayed correctly.
|
| /Documentation/networking/device_drivers/ethernet/intel/ |
| D | igb.rst | 89 This parameter adjusts the level debug messages displayed in the system logs.
169 the system log (displayed by the "dmesg" command):
|
| /Documentation/trace/ |
| D | ftrace.rst | 153 that is displayed in one of the above output
169 stored, and displayed by "trace". A new max trace will only be
202 for each CPU. The displayed number is the size of the
365 Similar to available_filter_functions, but with address displayed
366 for each function. The displayed address is the patch-site address
387 will be displayed on the same line as the function that
392 an 'I' will be displayed on the same line as the function that
395 If a non ftrace trampoline is attached (BPF) a 'D' will be displayed.
401 such cases an 'O' will be displayed.
436 content can be displayed in the files:
[all …]
|
| /Documentation/fb/ |
| D | internals.rst | 68 value, and that color is displayed.
|
| /Documentation/hwmon/ |
| D | ina209.rst | 27 calibration multiplier to scale the displayed current and power values.
|
12345