Searched full:dma1 (Results 1 – 16 of 16) sorted by relevance
| /Documentation/devicetree/bindings/dma/ |
| D | atmel-xdma.txt | 21 dma1: dma-controller@f0004000 {
47 dmas = <&dma1
50 <&dma1
|
| D | renesas,rzn1-dmamux.yaml | 49 dma-masters = <&dma0 &dma1>;
|
| D | brcm,bcm2835-dma.yaml | 83 "dma1",
|
| /Documentation/arch/arm/ |
| D | netwinder.rst | 15 0x0000 0x000f DMA1
19 0x0080 0x0087 DMA1
40 0x0480 0x0487 DMA1
|
| /Documentation/devicetree/bindings/spi/ |
| D | cirrus,ep9301-spi.yaml | 67 dmas = <&dma1 10 2>, <&dma1 10 1>;
|
| /Documentation/arch/arm/stm32/ |
| D | stm32-dma-mdma-chaining.rst | 77 | Channel *0* | DMA1 channel 0 | dma1_tcf0 | *0x00* |
79 | Channel *1* | DMA1 channel 1 | dma1_tcf1 | *0x01* |
81 | Channel *2* | DMA1 channel 2 | dma1_tcf2 | *0x02* |
83 | Channel *3* | DMA1 channel 3 | dma1_tcf3 | *0x03* |
85 | Channel *4* | DMA1 channel 4 | dma1_tcf4 | *0x04* |
87 | Channel *5* | DMA1 channel 5 | dma1_tcf5 | *0x05* |
89 | Channel *6* | DMA1 channel 6 | dma1_tcf6 | *0x06* |
91 | Channel *7* | DMA1 channel 7 | dma1_tcf7 | *0x07* |
|
| /Documentation/devicetree/bindings/dma/stm32/ |
| D | st,stm32-dmamux.yaml | 53 dma-masters = <&dma1>, <&dma2>;
|
| /Documentation/devicetree/bindings/pci/ |
| D | baikal,bt1-pcie.yaml | 49 - const: dma1
149 interrupt-names = "dma0", "dma1", "dma2", "dma3",
|
| D | rockchip-dw-pcie-common.yaml | 85 - const: dma1
|
| D | rockchip-dw-pcie-ep.yaml | 85 "dma0", "dma1", "dma2", "dma3";
|
| D | snps,dw-pcie-ep.yaml | 190 interrupt-names = "dma0", "dma1";
|
| /Documentation/sound/ |
| D | alsa-configuration.rst | 202 dma1
356 dma1
368 ``port``, ``wss_port``, ``irq`` and ``dma1`` have to be specified.
376 If ``dma2`` is specified and different from ``dma1``, the card will operate in
377 full-duplex mode. When ``dma1=3``, only ``dma2=0`` is valid and the only way to
380 Generic settings are ``port=0x220 wss_port=0x530 irq=10 dma1=1 dma2=0
398 dma1
410 ``port``, ``wss_port``, ``irq`` and ``dma1`` have to be specified.
418 If ``dma2`` is specified and different from ``dma1``, the card will operate in
419 full-duplex mode. When ``dma1=3``, only ``dma2=0`` is valid and the only way to
[all …]
|
| /Documentation/devicetree/bindings/powerpc/4xx/ |
| D | ppc440spe-adma.txt | 34 (typically 0x0 and 0x1 for DMA0 and DMA1)
|
| /Documentation/devicetree/bindings/interrupt-controller/ |
| D | brcm,bcm2835-armctrl-ic.txt | 62 17: DMA1
|
| /Documentation/admin-guide/ |
| D | pnp.rst | 106 pnp_reserve_dma=dma1[,dma2] ....
|
| /Documentation/networking/device_drivers/ethernet/ti/ |
| D | cpsw.rst | 361 | |dma7| |dma6| |dma3| |dma2| |dma1| |dma0| |dma4| |dma5| |
|