Home
last modified time | relevance | path

Searched full:gnd (Results 1 – 25 of 43) sorted by relevance

12

/Documentation/devicetree/bindings/iio/dac/
Dadi,ltc2664.yaml57 pins (MSP2, MSP1 and MSP0) to GND and/or VCC, any output range can be
61 0 - MPS2=GND, MPS1=GND, MSP0=GND (+-10V, reset to 0V)
62 1 - MPS2=GND, MPS1=GND, MSP0=VCC (+-5V, reset to 0V)
63 2 - MPS2=GND, MPS1=VCC, MSP0=GND (+-2.5V, reset to 0V)
64 3 - MPS2=GND, MPS1=VCC, MSP0=VCC (0V to 10, reset to 0V)
65 4 - MPS2=VCC, MPS1=GND, MSP0=GND (0V to 10V, reset to 5V)
66 5 - MPS2=VCC, MPS1=GND, MSP0=VCC (0V to 5V, reset to 0V)
67 6 - MPS2=VCC, MPS1=VCC, MSP0=GND (0V to 5V, reset to 2.5V)
Dadi,ltc2672.yaml70 41 kΩ can be used instead by connecting the resistor between FSADJ and GND
/Documentation/spi/
Dbutterfly.rst39 GND J403.GND pin 23/GND
52 GND J400.GND pin 24/GND
70 GND J403.GND pin 22/GND
73 GND J402.GND(P2) pin 25/GND
Dspi-lm70llp.rst47 GND 25 - GND 7
/Documentation/admin-guide/auxdisplay/
Dcfag12864b.rst65 (11) [GND]---( 2) Ground
67 (13) [GND]---(15) Read / Write
72 Ground (18)---[GND] [+5v]---(19) LED +
73 Ground (19)---[GND]
74 Ground (20)---[GND] E A Values:
75 Ground (21)---[GND] [GND]---[P1]---(18) Vee - R = Resistor = 22 ohm
76 Ground (22)---[GND] | - P1 = Preset = 10 Kohm
77 Ground (23)---[GND] ---- S ------( 3) V0 - P2 = Preset = 1 Kohm
78 Ground (24)---[GND] | |
79 Ground (25)---[GND] [GND]---[P2]---[R]---(20) LED -
/Documentation/ABI/testing/
Dsysfs-bus-iio-adc-hi84357 Could be either "GND-Open" or "Supply-Open" mode. Y is a
19 is separately set for "GND-Open" and "Supply-Open" modes.
38 is separately set for "GND-Open" and "Supply-Open" modes.
/Documentation/devicetree/bindings/iio/adc/
Dti,ads1015.yaml61 4: Voltage over AIN0 and GND.
62 5: Voltage over AIN1 and GND.
63 6: Voltage over AIN2 and GND.
64 7: Voltage over AIN3 and GND.
Dti,adc12138.yaml40 (Note that this must not go below GND or exceed vref-p)
Dmaxim,max34408.yaml53 SHTDN Enable Input. CMOS digital input. Connect to GND to clear the latch and
Dqcom,spmi-vadc.yaml112 specified VADC will use the VDD reference (1.8V) and GND for
118 the VDD reference (1.875V) and GND for channel calibration. If
/Documentation/i2c/busses/
Di2c-parport.rst75 GND GND
88 - Pins 18-25 of the parallel port connected to GND.
135 GND GND
/Documentation/input/devices/
Dwalkera0701.rst21 pin 3 is GND. Between pin 3 and CPU 5k6 resistor can be found. To get
31 / O 4 3 O \ pin 3 (GND) LED ________________ 10 ACK
35 ------- 3 __________________________________|________________ 25 GND
/Documentation/devicetree/bindings/iio/afe/
Dtemperature-transducer.yaml48 | GND
50 GND
Dvoltage-divider.yaml30 GND
Dtemperature-sense-rtd.yaml45 GND
/Documentation/devicetree/bindings/sound/
Dqcom,pm8916-wcd-analog-codec.yaml78 qcom,gnd-jack-type-normally-open:
81 True if the GND pin on the jack is NO (Normally Open), false if it's
Dqcom,wcd938x.yaml27 description: GPIO spec for swapping gnd and mic segments
/Documentation/devicetree/bindings/iio/proximity/
Dmurata,irsd200.yaml25 When the AD pin is connected to GND, the slave address is 0x48.
Dsemtech,sx9324.yaml137 - gnd
201 semtech,cs-idle-sleep = "gnd";
/Documentation/devicetree/bindings/hwmon/
Dntc-thermistor.yaml45 + GND GND
/Documentation/devicetree/bindings/mtd/
Djedec,spi-nor.yaml87 flash device is not connected or is wrongly tied to GND (that includes internal
90 the SRWD bit while writing the status register. WP# signal hard strapped to GND
/Documentation/devicetree/bindings/mfd/
Drohm,bd71815-pmic.yaml76 The BD71815 has undocumented GPO at pin E5. Pin is marked as GND at the
77 data-sheet as its location in the middle of GND pins makes it hard to
Dtps6507x.txt29 0: If defdcdc pin of DCDC2/DCDC3 is pulled to GND.
/Documentation/devicetree/bindings/mmc/
Datmel,sama5d2-sdhci.yaml53 SAMA5D2, the pin is usually tied to the GND with a resistor and a
/Documentation/devicetree/bindings/gpio/
Dgpio-delay.yaml30 GND

12