Home
last modified time | relevance | path

Searched +full:gpio +full:- +full:restart (Results 1 – 6 of 6) sorted by relevance

/Documentation/devicetree/bindings/power/reset/
Dgpio-restart.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/power/reset/gpio-restart.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: GPIO controlled reset
10 - Sebastian Reichel <sre@kernel.org>
13 Drive a GPIO line that can be used to restart the system from a restart handler.
16 request the given gpio line and install a restart handler. If the optional properties
17 'open-source' is not found, the GPIO line will be driven in the inactive state. Otherwise its
18 not driven until the restart is initiated.
[all …]
Dgpio-poweroff.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/power/reset/gpio-poweroff.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: GPIO controlled power off
10 - Sebastian Reichel <sre@kernel.org>
13 System power off support via a GPIO line. When a shutdown is
14 executed the operating system is expected to switch the GPIO
15 from inactive to active. After a delay (active-delay-ms) it
17 delay (inactive-delay-ms) it is configured as active again.
[all …]
/Documentation/driver-api/gpio/
Ddrivers-on-gpio.rst2 Subsystem drivers using GPIO
5 Note that standard kernel drivers exist for common GPIO tasks and will provide
6 the right in-kernel and userspace APIs/ABIs for the job, and that these
10 - leds-gpio: drivers/leds/leds-gpio.c will handle LEDs connected to GPIO
13 - ledtrig-gpio: drivers/leds/trigger/ledtrig-gpio.c will provide a LED trigger,
14 i.e. a LED will turn on/off in response to a GPIO line going high or low
15 (and that LED may in turn use the leds-gpio as per above).
17 - gpio-keys: drivers/input/keyboard/gpio_keys.c is used when your GPIO line
20 - gpio-keys-polled: drivers/input/keyboard/gpio_keys_polled.c is used when your
21 GPIO line cannot generate interrupts, so it needs to be periodically polled
[all …]
/Documentation/admin-guide/media/
Dcec.rst1 .. SPDX-License-Identifier: GPL-2.0
12 - Exynos4
13 - Exynos5
14 - STIH4xx HDMI CEC
15 - V4L2 adv7511 (same HW, but a different driver from the drm adv7511)
16 - stm32
17 - Allwinner A10 (sun4i)
18 - Raspberry Pi
19 - dw-hdmi (Synopsis IP)
20 - amlogic (meson ao-cec and ao-cec-g12a)
[all …]
/Documentation/networking/
Dcan.rst2 SocketCAN - Controller Area Network
20 .. _socketcan-motivation:
29 functionality. Usually, there is only a hardware-specific device
32 Queueing of frames and higher-level transport protocols like ISO-TP
34 character-device implementations support only one single process to
47 protocol family module and also vice-versa. Also, the protocol family
57 communicate using a specific transport protocol, e.g. ISO-TP, just
60 CAN-IDs, frames, etc.
62 Similar functionality visible from user-space could be provided by a
74 * **Abstraction:** In most existing character-device implementations, the
[all …]
/Documentation/watchdog/
Dwatchdog-parameters.rst7 be listed here unless the driver has its own driver-specific information
10 See Documentation/admin-guide/kernel-parameters.rst for information on
14 -------------------------------------------------
21 timeout. Setting this to a non-zero value can be useful to ensure that
25 -------------------------------------------------
36 -------------------------------------------------
49 -------------------------------------------------
58 -------------------------------------------------
64 Use the gpio watchdog (required by old cobalt boards).
70 -------------------------------------------------
[all …]