Searched full:ground (Results 1 – 25 of 41) sorted by relevance
12
| /Documentation/devicetree/bindings/mfd/ |
| D | samsung,s2mps11.yaml | 45 samsung,s2mps11-acokb-ground:
47 Indicates that ACOKB pin of S2MPS11 PMIC is connected to the ground so
53 samsung,s2mps11-wrstbi-ground:
79 samsung,s2mps11-wrstbi-ground: false
90 samsung,s2mps11-acokb-ground: false
101 samsung,s2mps11-acokb-ground: false
102 samsung,s2mps11-wrstbi-ground: false
113 samsung,s2mps11-acokb-ground: false
114 samsung,s2mps11-wrstbi-ground: false
125 samsung,s2mps11-acokb-ground: false
[all …]
|
| D | mediatek,mt6357.yaml | 43 the audio reference ground.
|
| /Documentation/admin-guide/auxdisplay/ |
| D | cfag12864b.rst | 65 (11) [GND]---( 2) Ground
72 Ground (18)---[GND] [+5v]---(19) LED +
73 Ground (19)---[GND]
74 Ground (20)---[GND] E A Values:
75 Ground (21)---[GND] [GND]---[P1]---(18) Vee - R = Resistor = 22 ohm
76 Ground (22)---[GND] | - P1 = Preset = 10 Kohm
77 Ground (23)---[GND] ---- S ------( 3) V0 - P2 = Preset = 1 Kohm
78 Ground (24)---[GND] | |
79 Ground (25)---[GND] [GND]---[P2]---[R]---(20) LED -
|
| /Documentation/devicetree/bindings/hwmon/ |
| D | ntc-thermistor.yaml | 19 When used in practice, a thermistor is often connected between ground, a
34 / | | "connected ground"
48 called "connected ground" and "connected positive" and shall be understood as
56 connected to ground and we get the thermistor under the pull-up resistor
61 ground" and "connected positive" cases.
114 to be connected-ground, which usually means a pull-down resistance of
|
| /Documentation/devicetree/bindings/iio/adc/ |
| D | fsl,imx25-gcq.yaml | 96 0: XN ground reference
97 1: YN ground reference
98 2: Internal ground reference
99 3: External ground reference (default)
|
| D | ti,adc12138.yaml | 41 If not specified, this is assumed to be analog ground.
|
| /Documentation/input/devices/ |
| D | joystick-parport.rst | 87 Ground is quite easy. On PC's parallel port the ground is on any of the
88 pins from pin 18 to pin 25. So use any pin of these you like for the ground::
90 (pin 18) -----> Ground
126 | o o o o | | | | | +-> Ground
129 | | | +-> Ground | +------------------> Clock
137 | +-------> Latch | +---> Ground
146 +--------> Ground +----------------> Power
171 +--------> Ground
192 +--------> Ground | +--------> Output 3
193 +----------> Ground
[all …]
|
| /Documentation/hwmon/ |
| D | ntc_thermistor.rst | 56 -+- (ground)
68 -+- (ground)
80 -+----+- (ground)
92 -+- (ground)
|
| D | ltc4260.rst | 47 of the divider resistor against Ground.
|
| D | ltc4261.rst | 47 of the divider resistor against Ground.
|
| D | ltc2945.rst | 47 of the divider resistor against Ground.
|
| /Documentation/devicetree/bindings/iio/proximity/ |
| D | semtech,sx9310.yaml | 46 semtech,cs0-ground:
47 description: Indicates the CS0 sensor is connected to ground.
124 semtech,cs0-ground;
|
| /Documentation/devicetree/bindings/sound/ |
| D | qcom,wcd93xx-common.yaml | 61 qcom,ground-jack-type-normally-closed:
62 description: Indicates that Headset Ground switch type is normally closed
|
| D | qcom,wcd934x.yaml | 86 qcom,ground-jack-type-normally-closed:
87 description: Indicates that Headset Ground switch type is normally closed
221 qcom,ground-jack-type-normally-closed;
|
| D | qcom,wcd938x.yaml | 49 qcom,ground-jack-type-normally-closed;
|
| D | qcom,wcd939x.yaml | 67 qcom,ground-jack-type-normally-closed;
|
| D | realtek,rt5645.yaml | 65 sleeve/ring2 contacts to the ground or floating. It could avoid some
|
| /Documentation/devicetree/bindings/leds/ |
| D | richtek,rt8515.yaml | 60 ground. The maximum hardware current setting is calculated
72 ground. The maximum hardware current setting is calculated
|
| /Documentation/devicetree/bindings/iio/dac/ |
| D | maxim,ds4424.yaml | 41 reg = <0x10>; /* When A0, A1 pins are ground */
|
| /Documentation/devicetree/bindings/iio/ |
| D | mount-matrix.txt | 96 ground plane and positive towards magnetic North, (x) is in the ground plane,
98 perpendicular to the ground plane and positive upwards.
|
| /Documentation/w1/ |
| D | w1-generic.rst | 6 signal wire (plus ground, so two wires).
8 Devices communicate on the bus by pulling the signal to ground via an open
|
| /Documentation/devicetree/bindings/gpio/ |
| D | nxp,pcf8575.yaml | 14 driven high by a pull-up current source or driven low to ground. This
|
| /Documentation/admin-guide/media/ |
| D | cec.rst | 336 The ground pin of the HDMI connector needs to be connected to a ground
373 and two female-female breadboard wires: one for connecting the HDMI ground
374 pin to a ground pin on the Raspberry Pi, and the other to connect the HDMI
|
| /Documentation/networking/ |
| D | plip.rst | 152 GROUND 25 - 25
186 GROUND 25 - 25
|
| /Documentation/misc-devices/ |
| D | lis3lv02d.rst | 95 fall to the ground is out of question...
|
12