Searched full:hooked (Results 1 – 25 of 32) sorted by relevance
12
| /Documentation/devicetree/bindings/media/cec/ |
| D | cec-gpio.yaml | 14 hooked up to a pull-up GPIO line and - optionally - the HPD line is hooked up
|
| /Documentation/userspace-api/media/cec/ |
| D | cec-ioc-adap-g-phys-addr.rst | 66 has address 0.0.0.0. Every device that is hooked up to an input of the
67 TV has address a.0.0.0 (where 'a' is ≥ 1), devices hooked up to those in
|
| /Documentation/devicetree/bindings/display/ |
| D | dp-aux-bus.yaml | 14 are hooked up to them. This is the DP AUX bus. Over the DP AUX bus
|
| /Documentation/devicetree/bindings/interrupt-controller/ |
| D | fsl,ls-msi.yaml | 11 is hooked to a parent interrupt controller: e.g: ARM GIC for ARM-based
|
| D | brcm,bcm7120-l2-intc.yaml | 14 is hooked to a parent interrupt controller: e.g: ARM GIC for ARM-based
|
| /Documentation/admin-guide/LSM/ |
| D | index.rst | 6 various security checks to be hooked by new kernel extensions. The name
|
| /Documentation/devicetree/bindings/power/ |
| D | rockchip-io-domain.yaml | 18 If the regulator hooked up to a pin like SDMMC0_VDD is 3.3V then
19 bit 7 of GRF_IO_VSEL needs to be 0. If the regulator hooked up to
24 hooked up to the pins.
|
| /Documentation/devicetree/bindings/display/panel/ |
| D | panel-edp.yaml | 108 needed if HPD hooked up, either through a GPIO in the panel node or
109 hooked up directly to the eDP controller.
|
| D | panel-common.yaml | 84 (hot plug detect) signal, but the signal isn't hooked up so we should
|
| /Documentation/sound/soc/ |
| D | jack.rst | 69 These are all hooked together by the machine driver depending on the
|
| /Documentation/admin-guide/media/ |
| D | cec.rst | 58 - cec-gpio. If the CEC pin is hooked up to a GPIO pin then
147 are PS176 based and do NOT have the CEC pin hooked up, so only the three Club3D
152 likely to have the CEC pin hooked up, it looks like they changed the reference
363 If you haven't hooked up the HPD and/or 5V lines, then just delete those
|
| /Documentation/networking/ |
| D | phy-link-topology.rst | 85 These function are already hooked into the phylib subsystem, so all PHYs that
|
| D | ieee802154.rst | 75 Those types of devices require different approach to be hooked into Linux kernel.
|
| /Documentation/userspace-api/media/v4l/ |
| D | ext-ctrls-dv.rst | 20 hooked up to e.g. HDMI connectors. Even though the subdevice will
|
| /Documentation/driver-api/80211/ |
| D | mac80211-advanced.rst | 13 device LEDs should be exposed as LED class devices and hooked up to the
|
| /Documentation/devicetree/bindings/display/bridge/ |
| D | ti,sn65dsi86.yaml | 34 Set if the HPD line on the bridge isn't hooked up to anything or is
|
| /Documentation/arch/x86/ |
| D | earlyprintk.rst | 61 wired such that the EHCI debug controller is hooked up to the
|
| D | mds.rst | 203 The mitigation is hooked into all variants of halt()/mwait(), but does
|
| /Documentation/hid/ |
| D | hid-transport.rst | 180 - RESET: Used by I2C-HID, not hooked up in HID core.
181 - SET_POWER: Used by I2C-HID, not hooked up in HID core.
|
| /Documentation/trace/ |
| D | mmiotrace.rst | 121 calling one of the ioremap_*() functions. Mmiotrace is hooked into the
|
| /Documentation/admin-guide/ |
| D | rtc.rst | 29 same functionality. For example, not every RTC is hooked up to an
|
| /Documentation/gpu/amdgpu/display/ |
| D | dcn-overview.rst | 39 (Note that DWB is not hooked yet).
|
| /Documentation/leds/ |
| D | leds-class.rst | 52 to which given device is hooked is available in sysfs and can be
|
| /Documentation/mm/ |
| D | hmm.rst | 249 and HMM hooked itself in various places of mm code to handle any access to
|
| /Documentation/admin-guide/mm/ |
| D | numa_memory_policy.rst | 139 shmem segments were never "hooked up" to the shared policy support.
|
12