Searched full:int1 (Results 1 – 24 of 24) sorted by relevance
| /Documentation/devicetree/bindings/iio/accel/ |
| D | fsl,mma7455.yaml | 32 Data ready is only available on INT1, but events can use either or
34 to INT1 and second (where present) to INT2.
39 - INT1
64 interrupt-names = "INT2", "INT1";
79 interrupt-names = "INT1";
|
| D | bosch,bma255.yaml | 50 connected to the INT1 pin, the second (optional) interrupt listed must be
54 BMC156 does not have an INT1 pin, therefore the first interrupt pin is
62 - INT1
92 interrupt-names = "INT1";
|
| D | nxp,fxls8962af.yaml | 35 - INT1
63 interrupt-names = "INT1";
79 interrupt-names = "INT1";
|
| D | adi,adxl313.yaml | 46 - INT1
72 interrupt-names = "INT1";
89 interrupt-names = "INT1";
|
| D | kionix,kx022a.yaml | 35 - enum: [INT1, INT2]
64 interrupt-names = "INT1";
|
| D | adi,adxl380.yaml | 37 - enum: [INT0, INT1]
38 - const: INT1
|
| D | fsl,mma8452.yaml | 37 - INT1
|
| D | bosch,bmi088.yaml | 42 - INT1
|
| D | adi,adxl355.yaml | 38 - INT1
|
| /Documentation/devicetree/bindings/iio/imu/ |
| D | bosch,bmi160.yaml | 33 - INT1
36 set to "INT1" if INT1 pin should be used as interrupt input, set
77 interrupt-names = "INT1";
|
| D | bosch,bmi323.yaml | 37 - INT1
75 interrupt-names = "INT1";
|
| D | nxp,fxos8700.yaml | 33 - INT1
62 interrupt-names = "INT1";
|
| D | st,lsm6dsx.yaml | 62 Supports up to 2 interrupt lines via the INT1 and INT2 pins.
|
| /Documentation/devicetree/bindings/iio/gyroscope/ |
| D | nxp,fxas21002c.yaml | 43 - INT1
81 interrupt-names = "INT1";
|
| D | bosch,bmg160.yaml | 33 If two interrupts are provided, expected order is INT1 and INT2.
|
| /Documentation/devicetree/bindings/interrupt-controller/ |
| D | loongson,liointc.yaml | 116 interrupt-names = "int0", "int1";
119 <0x0f000000>, /* int1 */
|
| /Documentation/devicetree/bindings/iio/magnetometer/ |
| D | asahi-kasei,ak8974.yaml | 25 Data ready (DRDY) and interrupt (INT1) lines from the chip. The DRDY
|
| /Documentation/devicetree/bindings/net/can/ |
| D | bosch,m_can.yaml | 40 - const: int1
144 interrupt-names = "int0", "int1";
|
| D | microchip,mcp251xfd.yaml | 43 GPIO phandle of GPIO connected to to INT1 pin of the MCP251XFD, which
|
| /Documentation/devicetree/bindings/sound/ |
| D | ti,tlv320adc3xxx.yaml | 54 - 5 # ADC3XXX_GPIO_INT1 - INT1 output
72 - 5 # ADC3XXX_GPIO_INT1 - INT1 output
|
| /Documentation/devicetree/bindings/net/ |
| D | fsl,fec.yaml | 88 - const: int1
92 - const: int1
|
| /Documentation/ |
| D | dontdiff | 146 int1.c
|
| /Documentation/devicetree/bindings/iio/ |
| D | st,st-sensors.yaml | 101 Inertial interrupt lines INT1 and INT2 if these exist. This means up to
|
| /Documentation/devicetree/bindings/pinctrl/ |
| D | marvell,armada-xp-pinctrl.txt | 51 mpp30 30 gpio, tdm(int1), sd0(clk)
|